OPERATION
ELECTRONIC CONTROLS
Power Control
The Power Control turns the unit on and off.
Set Temperature/ Timer Display
Shows the set temperature when the unit is in operation and hours when the timer is being set. THE TEMPERATURE DISPLAY ONLY SHOWS THE SET TEMPERATURE, NOT THE ACTUAL ROOM TEMPERATURE.
Temperature/ Timer Hour Controls
These buttons are used to raise or lower the set temperature in increments of 1° from 66°F to 88°F. By depressing both buttons at once, the display will toggle between Celsius and Fahrenheit. When the timer is being set, these buttons are used to change the hour setting in increments of 1 from 00 to 24.
Mode Control
A green light will indicate which mode is currently being utilized.
Cool Mode –
The unit will circulate and cool the air.
Heat Mode (Heat Models Only) –
The unit will circulate and heat the air.
Heater Safety Feature- When heater is powered off, low fan will automatically stay on and run for 60 seconds to ensure the removal of residual heat, meanwhile, the Low Fan LED blinks until the low fan stops.
Fan Mode –
The unit will only circulate the air.
Energy Saver Mode –
(The energy saver mode is designed to operate with Cool mode only). The fan will switch from the set fan speed to Low whenever the compressor turns off in response to the thermostat. When the compressor cycles back on, the unit will return to the original fan setting. Speeds will change automatically as the temperature in the room changes.
Fan Speed Control - High, Medium, Low and Auto
The settings are adjusted with the Fan Speed Control, each time the button is depressed it changes the setting. A green light will indicate which setting is currently being used.
When the Auto feature is selected while the air conditioner is in the Cool or Heat mode, the fan speeds will change automatically as the temperature in the room changes. In Cool Mode when the room reaches 7° or more above the set temperature High Fan will be used, 4° or less above the set temperature will use Low fan. In Heat Mode when the room reaches 7° or more below the set temperature High fan will be used, 4° or less below the set temperature will use Low fan. At all other times the fan will use Medium fan.
Timer Control (The timer can be set to either turn the unit on or off.)
To automatically START the unit using the Timer mode:
1.Push the timer button while the power is OFF. The display will read 00. Adjust the display to show the desired number of hours before
2.The display will show the amount of time, in hours, remaining until
3.To exit Timer mode, push the Timer button.
4.A green light next to the Timer button indicates that the timer is set.
To automatically
1.Push the timer button while the power is ON. The display will read 00. Adjust the display to show the desired number of hours before
2.To display the amount of time left until
3.To exit Timer mode, push the Timer button twice.
4.A green light next to the Timer button indicates that the timer is set.
Electronic Control (Cooling Only) | |
A |
|
B | D |
| |
C |
|
F |
|
| E |
Electronic Control (Heat/Cool)
A
| B | D |
|
| |
| High | Auto |
Timer |
|
|
C | Med | Low |
| Heat |
|
On/Off | Cool |
|
Energy Save | ||
F | Fan |
|
Built in Three Minute Cooling Delay |
| E |
A Temperature/Timer Display
BTemperature/Timer Adjustment
CTimer On/Off
DFan Speed Control
EMode Control
FPower Control
If this electronic unit will not respond to touch pad or remote control commands, it is necessary to unplug the unit from the electrical outlet for five seconds and then plug the unit back in.
Auto restart feature:
In the event of a power failure, this feature allows the unit to resume operation once power has been restored, retaining the most recent settings. Upon restoration of power, the timer mode may need to be reset if being utilized.
CAUTION
Heat/Cool models or units with electric heat are designed to be used only as a supplemental heat source. They should be used in addition to regular heating systems and never as the primary source of heat.
6
