FieldServer FS-8700-47 instruction manual

FS-8700-47 DNP 3.0 Driver Manual		Page 48 of 51
	Error Message	Explanation
	DNP:#45 Err. Dest	If the destination address is 0xFFFF (=65535) then this message is
		printed. The address 0xFFFF is the broadcast address and the
	Address=%d=Broadcast
		driver cannot process broadcasts. Configure the node which sent
	Address." , dest_station
		the broadcast message to send a specific message to the
	DNP:#45 Err. Perhaps the	FieldServer. 8
		We have also seen that this message gets printed when the
	System_Station_Address has not
		‘System_Station_Address’ has not been specified. Appendix A.12
	been specified."
		has more information.
		A message was received by the Server side for a Node that has not
		been defined (as a DNP node).
	DNP:#46 Err. Server received a
	poll for unknown node=%d	Either this message wasn’t intended for the FieldServer or the
		configuration requires review. You may need to add a new Server
		side node and Server side Map Descriptors to solve this problem.
	DNP:#49 Err. Cant process	The driver cannot process the function code indicated when the
	func=0x%x from a responder	message comes from a responder. If this message occurs rarely
		then assume it is the result of an occasional corrupt message. If
	DNP:#50 Err. Cant process	you are concerned or if it occurs frequently then take a log and
	func=0x%x from an initiator	contact Tech Support.
	DNP:#51 Err. Node_ID=%d Valid	Illegal Node_ID used. The Node ID refers to the DNP 3.0 Station
	Range=0-65535	Address. Refer to sections 4.3 and 5.2.
		The message reports that the driver has been set to a mode where
	DNP3:#52a FYI. OriginalStyle DA	it will use the DA offsetting style present in the driver prior to
	offset use.	version 1.02a. If this is consistent with your configuration, the
		message may be ignored.
		A response to a poll contained no data. This is possible when, for
	DNP3:#53 FYI. Mast App Parse -	example, you poll for event or change data and no events/changes
	NO DATA, returning early	have occurred since the last poll. This message is printed for
		information purposes only
	DNP3:#53b FYI. Class Rqst	As per #53 but pertains exclusively to polls for class data.
	returned no data.
	DNP:#54 Err. App Layer	A message was received by the Server side and the application
		layer function code isn’t supported by this driver. You could
	Func=%#x not recognized.
		reconfigure the Client not to send this message,
	DNP:#55 Err. To serve class data	When you create MD’s to serve Class Data the dnpAssoc field must
		have non-zero values. More information is provided in section
	set the DNPAssoc value non-zero	5.3.58
		To serve Class data you need a Map Descriptor matching the class
	DNP:#56 Err. No MDs associated	data request and a number of associated Map Descriptors to tell
	with the class MD=%s	the driver what data forms part of the class data set. More
		information is provided in section 5.3.58
	DNP:#57 FYI. You could have	Error! Reference source not found. and 0 contain additional
	used a MD called <dnp-stats> to
		information.
	expose diagnostic info.
	DNP3:#58 Err. Response	The driver found that a response message was addressed to a
		node different from the polling node. Take a log and report to Tech
	Dest=%d != Master=%d
		support.
		The response message originated from a node different to the
	DNP3:#59 Err. Response	polled node. If the Node_ID reported is not in the list of nodes in
		your configuration, take a log and report the problem to Tech
	Unknown Src_Id=%d
		Support. If this message is printed rarely, it may have resulted from
		an occasional corrupt message.

8Edit the CSV file, download to the FieldServer and reset the FieldServer.

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com