Controls and Connections, Getting Started, Shx0001f.gif | Fluke 271

Getting Started

Getting Started

Controls and Connections

Controls and Connections

shx0001f.gif

Figure 1. Model 271 Front Panel

3

Image 13

Fluke manual Controls and Connections, Getting Started, Model 271 Front Panel, shx0001f.gif

Contents

Programmable 10 MHz DDS Function Generator Getting Started Manual To register your product online, visit register.fluke.com LIMITED WARRANTY AND LIMITATION OF LIABILITY Safety Getting Started Manual The following symbols are used on the instrument and in this manual Safety continuedTerminal connected to chassis ground Mains supply OFF Mains supply ON Alternating current Warning - hazardous voltages may be presentPage Emissions EMC ComplianceImmunity e EN61000-4-5 1995 Surge 0.5 kV line to line, 1 kV line to ground Title Table of Contents AUX OUT viii Introduction Getting StartedBefore You Start Mains Supply Voltage Externally Applied Voltages Getting Started Controls and ConnectionsFigure 1. Model 271 Front Panel shx0001f.gif Controls The Liquid Crystal DisplayFunction Keys FIELD and DIGIT Keys and the Rotary Control Numeric, Units and SET Keys UTILITIES Keys MODE KeysOUTPUT Key RECALL and REMOTE EXT TRIG Front Panel Inputs and OutputsMAIN OUT AUX OUT CLOCK IN/OUT Rear Panel ConnectorsVCA IN SYNC OUT TRIG/SWEEP OUT RS232 and GPIB Interface Connectors Plug in and switch on the instrument Using the InstrumentStarting up Check the LCD Display Set a frequency, for example 12.5 kHz Generating Continuous SignalsFREQ=12.50000kHz VhiZ=+20.0 Vpp 50Ω DC=+0.00mV +0.00mV SYM=50.0% 50.0% Have a look at some other waveforms Set the amplitude to +10 dBmChange the dc offset =80.00000us DC OFFSET CHANGE * * BY OUTPUT LEVEL Effect of the output attenuatorPER =80.00000us VhiZ=+4.00 Vpp 50Ω DC=+1.50 V +151.mV SYM=50.0% 50.0% SOURCE=EXT TGEN=1.00ms 1.000kHz BURST COUNT= PHASE=+000 +000 Adjusting the phaseSOURCE=EXT TGEN=1.00ms 1.000kHz BURST COUNT= PHASE=+116 +116 Asymmetric waveforms TRIG/SWEEP OUT signal Generating Swept Signals MODE=BEG-END LAW=LOG RAMP TIME=5.00 s TRIG SRC=CONTINUOUS MORE MODE=BEG-END LAW=LOG RAMP TIME=0.05 s TRIG SRC=CONTINUOUS MOREBEG FRQ=261.6000 Hz END FRQ=1.108700kHz MARK FRQ=523.3000 Hz MORE PHASE=+000 +000 SOURCE=EXT TGEN=1.00ms 1.000kHz BURST COUNT=0001 PHASE=+000 +000Generating a Triggered Burst FREQ=2.000000kHz VhiZ=+20.0 Vpp 50Ω DC=+0.00mV +0.00mV Special Waveforms FSK ModeStaircases FREQ A=800.0000 Hz FREQ B=1.200000kHz SOURCE=TGEN FREE Figure 2. 625-line PAL TV Signal name stepstart µs amplitude VALS=ABS AUTO=YES STEP=08 ACTIVE LENGTH=0005 LEVEL=+153 VALS=ABS AUTO=YES STEP=01 ACTIVE LENGTH=0256 LEVEL=+000 Arbitrary Waveforms Saving and Recalling SettingsRECALL ARB No SINX/X ENTER TO EXECUTE RECALL ARB No ARB 03 IS EMPTY Other Functions and Waveforms