Fluke 9011 3 Quick Start

3 Quick Start

3.1 Unpacking

Unpack the dry-well carefully and inspect it for any damage that may haveoc-

curred during shipment. If there is shipping damage, notify the carrier

immediately.

Verifythat the following components are present:

•9011 Dry-well

•Power Cord

•User's Guide with Report of Calibration

•2 inserts

•Insert removal tool

•RS-232 Cable

•9930 Interface-it Software

3.2 Set-up

Place the calibrator on a flat surface with at least 6 inches of free space around

the instrument. Always leaveenough clearance in front of the instrument to al-

low for safe and easy insertion and removalof probes. Plug the power cord into

a grounded mains outlet. Observe that the nominal voltagecorresponds to that

indicated on the calibrator.

3.3 Power

Plug the instrument power cord into a mains outlet of the proper voltage,fre-

quency,and cu rrent capability.Refer to Section 2.1, Specifications, for the

power details.

Turn on the power to the calibrator by toggling both power switches on within

three seconds of each other.The fans should begin blowing air through the in-

strument and both controller displays should illuminate after 3 seconds. After a

brief self-test the controller should begin normal operation. If the unit failsto

operate please check the power connection.

NOTE: If more than three seconds elapse, (Interconnect Link) ap-

pears on the display. Press any front control panel button to eliminate the

message. The hot block serial commands are not available unless

both power switches were turned on within three seconds of each other.

The display shows the well temperature and the well heater brings the tempera-

ture of the well to the set-point temperature.

11

3 Quick Start

Unpacking

Contents

Main Page Table of Contents 7 Digital Communication Interface . . . . . . . . . . . . . . . . 37 8 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page Figures and Tables 1 Before You Start 1.1 Introduction 1.2 Symbols Used Tabl e1 International Electrical Symbols 2 1.3 Safety Information 1.3.1 WARNINGS Page 1.3.2 CAUTIONS 1.4 Authorized Service Centers Page 2 Specifications and Environmental Conditions 2.1 Specifications -it 2.2 Environmental Conditions 9 2.3 Warranty 3 Quick Start 3.1 Unpacking 3.2 Set-up 3.3 Power 3.4 Setting the Temperature 4 Parts and Controls 4.1 Rear Panel 4.2 Front Panel 4.3 Top Panel 4.4 Constant Temperature Block Assembly 9011 Dual-Well Calibrator 16 Insert A Cold block insert shown (Hot block C insert includes eight 1/4" wells) 5 General Operation 5.1 Setting the Temperature 5.2 Changing Display Units Un= C 6 Controller Operation 6.1 Well Temperature 100.00C 6.2 Temperature Set-point 6.2.1 Programmable Set-points 20 SET Select Setpoint Adjust Setpoint Units C/F Scan On/Off Scan Rate Figure 4 Controller Operation Flow Chart Cold Side Only DO NOT CHANGE THESE VALUES S 6.3 Scan 6.3.1 Scan Control Sc=OFF Sc=On S 6.3.2 Scan Rate Sr=2.0 Sr=3.0 S 6.4 Temperature Display Hold 6.4.1 Switch Status 6.4.2 Scan Hold 6.5 Ramp and Soak Program Menu 20.00C S+U ProG S 6.5.1 Number of Program Set-points Pn=8 E Pf=1 Pf=4 6.5.5 Program Control P=OFF S 6.6 Set-point Resistance 99.222 6.7 Secondary Menu 6.8 Heater Power S+E SEC 12.0P 6.9 Proportional Band S+E SEC 12.0P S ProP 4.1 10.0 S 6.10 Controller Configuration 6.11 Operating Parameters PAr 6.12 High Limit S 6.13 Serial Interface Parameters Page 6.13.4 Linefeed (cold side only) LF LF=On LF=OFF 6.14 Calibration Parameters CAL Page S Page 7 Digital Communication Interface 7.1 Serial Communications 7.1.1 Wiring 7.1.2 Setup Page 7.1.3 Serial Operation 7.2 Interface Commands 40 Tabl e 2 Controller Communications Commands 41 7 Digital Communication Interface Interface Commands Controller Communications Commands continued 42 Controller Communications Commands continued 8 Test Probe Calibration 8.1 Calibrating a Single Probe 8.2 Dry-well Characteristics 8.2.1 Stabilization and Accuracy Page 9 Calibration Procedure 9.1 Calibration Procedure 9.1.1 Calibration Equipment 9.1.2 Calibration Page 10 Maintenance 11 Troubleshooting 11.1 Troubleshooting Problems, Possible Causes, and Solutions 11.2 CE Comments 11.2.1 EMC Directive 11.2.2 Low Voltage Directive (Safety)