Fluke 9011 S

38530 Current ALPHA setting

Tochange the ALPHA setting, press “UP” or “DOWN”.

38600 New ALPHA setting

Toaccept the new setting, press “SET”. Press “EXIT” to continue without stor-

ing the new value.

SAccept the new ALPHA setting

6.14.4 DELTA

This probe parameter characterizes the curvature of the resistance-temperature

relationship of the sensor.The value of this parameter is set at the factory for

best instrument accuracy.

deLta Flashes for one second and then the DELTA setting is

displayed

1.5070 Current DELTA setting

Tochange the DELTA setting, press “UP” or “DOWN”.

1.6320 New DELTA setting

Toaccept the new setting, press “SET”. Press “EXIT” to continue without stor-

ing the new value.

SAccept the new DELTA setting

6.14.5 BETA (cold side only)

This probe parameter relates to the higher order nonlinearity of the sensor be-

low 0°C. The value is set at the factory for best instrument accuracy.

bEtA Flashes for one second and then the BETA setting is

displayed

0.111 Current BETA setting

Tochange the BETA setting, press “UP” or “DOWN”.

0.100 New BETA setting

Toaccept the new setting, press “SET”. Press “EXIT” to continue without stor-

ing the new value.

9011 Dual-Well Calibrator

User’s Guide

34

Contents

Main Page Table of Contents 7 Digital Communication Interface . . . . . . . . . . . . . . . . 37 8 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page Figures and Tables 1 Before You Start 1.1 Introduction 1.2 Symbols Used Tabl e1 International Electrical Symbols 2 1.3 Safety Information 1.3.1 WARNINGS Page 1.3.2 CAUTIONS 1.4 Authorized Service Centers Page 2 Specifications and Environmental Conditions 2.1 Specifications -it 2.2 Environmental Conditions 9 2.3 Warranty 3 Quick Start 3.1 Unpacking 3.2 Set-up 3.3 Power 3.4 Setting the Temperature 4 Parts and Controls 4.1 Rear Panel 4.2 Front Panel 4.3 Top Panel 4.4 Constant Temperature Block Assembly 9011 Dual-Well Calibrator 16 Insert A Cold block insert shown (Hot block C insert includes eight 1/4" wells) 5 General Operation 5.1 Setting the Temperature 5.2 Changing Display Units Un= C 6 Controller Operation 6.1 Well Temperature 100.00C 6.2 Temperature Set-point 6.2.1 Programmable Set-points 20 SET Select Setpoint Adjust Setpoint Units C/F Scan On/Off Scan Rate Figure 4 Controller Operation Flow Chart Cold Side Only DO NOT CHANGE THESE VALUES S 6.3 Scan 6.3.1 Scan Control Sc=OFF Sc=On S 6.3.2 Scan Rate Sr=2.0 Sr=3.0 S 6.4 Temperature Display Hold 6.4.1 Switch Status 6.4.2 Scan Hold 6.5 Ramp and Soak Program Menu 20.00C S+U ProG S 6.5.1 Number of Program Set-points Pn=8 E Pf=1 Pf=4 6.5.5 Program Control P=OFF S 6.6 Set-point Resistance 99.222 6.7 Secondary Menu 6.8 Heater Power S+E SEC 12.0P 6.9 Proportional Band S+E SEC 12.0P S ProP 4.1 10.0 S 6.10 Controller Configuration 6.11 Operating Parameters PAr 6.12 High Limit S 6.13 Serial Interface Parameters Page 6.13.4 Linefeed (cold side only) LF LF=On LF=OFF 6.14 Calibration Parameters CAL Page S Page 7 Digital Communication Interface 7.1 Serial Communications 7.1.1 Wiring 7.1.2 Setup Page 7.1.3 Serial Operation 7.2 Interface Commands 40 Tabl e 2 Controller Communications Commands 41 7 Digital Communication Interface Interface Commands Controller Communications Commands continued 42 Controller Communications Commands continued 8 Test Probe Calibration 8.1 Calibrating a Single Probe 8.2 Dry-well Characteristics 8.2.1 Stabilization and Accuracy Page 9 Calibration Procedure 9.1 Calibration Procedure 9.1.1 Calibration Equipment 9.1.2 Calibration Page 10 Maintenance 11 Troubleshooting 11.1 Troubleshooting Problems, Possible Causes, and Solutions 11.2 CE Comments 11.2.1 EMC Directive 11.2.2 Low Voltage Directive (Safety)