Fluke 9011 1.2 Symbols Used

1.2 Symbols Used

Table1 lists the International Electrical Symbols. Some or all of these symbols

may be used on the instrument or in this manual.

Symbol Description

AC (Alternating Current)

AC-DC

Battery

Complies with European Union directives

Double Insulated

Electric Shock

Fuse

PE Ground

Hot Surface(Bur n Hazard)

Read the User’sManual (Important Information)

Off

Canadian Standards Association

9011 Dual-Well Calibrator

User’s Guide

2 Tabl e1 International Electrical Symbols

Contents

Main Page Table of Contents 7 Digital Communication Interface . . . . . . . . . . . . . . . . 37 8 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page Figures and Tables 1 Before You Start 1.1 Introduction 1.2 Symbols Used Tabl e1 International Electrical Symbols 2 1.3 Safety Information 1.3.1 WARNINGS Page 1.3.2 CAUTIONS 1.4 Authorized Service Centers Page 2 Specifications and Environmental Conditions 2.1 Specifications -it 2.2 Environmental Conditions 9 2.3 Warranty 3 Quick Start 3.1 Unpacking 3.2 Set-up 3.3 Power 3.4 Setting the Temperature 4 Parts and Controls 4.1 Rear Panel 4.2 Front Panel 4.3 Top Panel 4.4 Constant Temperature Block Assembly 9011 Dual-Well Calibrator 16 Insert A Cold block insert shown (Hot block C insert includes eight 1/4" wells) 5 General Operation 5.1 Setting the Temperature 5.2 Changing Display Units Un= C 6 Controller Operation 6.1 Well Temperature 100.00C 6.2 Temperature Set-point 6.2.1 Programmable Set-points 20 SET Select Setpoint Adjust Setpoint Units C/F Scan On/Off Scan Rate Figure 4 Controller Operation Flow Chart Cold Side Only DO NOT CHANGE THESE VALUES S 6.3 Scan 6.3.1 Scan Control Sc=OFF Sc=On S 6.3.2 Scan Rate Sr=2.0 Sr=3.0 S 6.4 Temperature Display Hold 6.4.1 Switch Status 6.4.2 Scan Hold 6.5 Ramp and Soak Program Menu 20.00C S+U ProG S 6.5.1 Number of Program Set-points Pn=8 E Pf=1 Pf=4 6.5.5 Program Control P=OFF S 6.6 Set-point Resistance 99.222 6.7 Secondary Menu 6.8 Heater Power S+E SEC 12.0P 6.9 Proportional Band S+E SEC 12.0P S ProP 4.1 10.0 S 6.10 Controller Configuration 6.11 Operating Parameters PAr 6.12 High Limit S 6.13 Serial Interface Parameters Page 6.13.4 Linefeed (cold side only) LF LF=On LF=OFF 6.14 Calibration Parameters CAL Page S Page 7 Digital Communication Interface 7.1 Serial Communications 7.1.1 Wiring 7.1.2 Setup Page 7.1.3 Serial Operation 7.2 Interface Commands 40 Tabl e 2 Controller Communications Commands 41 7 Digital Communication Interface Interface Commands Controller Communications Commands continued 42 Controller Communications Commands continued 8 Test Probe Calibration 8.1 Calibrating a Single Probe 8.2 Dry-well Characteristics 8.2.1 Stabilization and Accuracy Page 9 Calibration Procedure 9.1 Calibration Procedure 9.1.1 Calibration Equipment 9.1.2 Calibration Page 10 Maintenance 11 Troubleshooting 11.1 Troubleshooting Problems, Possible Causes, and Solutions 11.2 CE Comments 11.2.1 EMC Directive 11.2.2 Low Voltage Directive (Safety)