Fluke 9011 S, S

6.3 Scan

The scan rate can be set and enabled so that when the set-pointis changed the

dry-well heats or cools at a specified rate (degrees per minute) until it reaches

the new set-point. Withthe scan disabled the dry-well heats or cools at the

maximum possible rate.

6.3.1 Scan Control

The scan is controlled with the scan on/offfunction that appears in the main

menu after the temperature scale units.

Sc=OFF Current scan setting

Press “UP” or “DOWN” to toggle the scan on or off.

Sc=On Scan function on

Press “SET” to accept the present setting and continue.

SAccept scan setting

6.3.2 Scan Rate

The scan rate can be set from 0.1 to 50.0°C/min. The maximum scan rate, how-

ever,is actually limited by the natural heatin g or cooling rate of the instrument.

This rate is often less than 50°C/min, especiallywhen cooling.

The scan rate function appears in the main menu after the scan controlfunction.

The scan rate units are in degrees Celsius per minute, regardless of the selected

units.

Sr=2.0 Current scan rate setting in °C/min

Press“UP”or“DOWN”tochangethescanrate.

Sr=3.0 New scan rate

Press “SET” to accept the new scan rate and continue.

SAccept scan rate

6.4 Temperature Display Hold

There are two sets of display hold terminalslocated on the top of the 9011, one

for the cold side and one for the hot side. The display hold terminals are used

for testing thermal switches.

9011 Dual-Well Calibrator

User’s Guide

22

Contents

Main Page Table of Contents 7 Digital Communication Interface . . . . . . . . . . . . . . . . 37 8 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page Figures and Tables 1 Before You Start 1.1 Introduction 1.2 Symbols Used Tabl e1 International Electrical Symbols 2 1.3 Safety Information 1.3.1 WARNINGS Page 1.3.2 CAUTIONS 1.4 Authorized Service Centers Page 2 Specifications and Environmental Conditions 2.1 Specifications -it 2.2 Environmental Conditions 9 2.3 Warranty 3 Quick Start 3.1 Unpacking 3.2 Set-up 3.3 Power 3.4 Setting the Temperature 4 Parts and Controls 4.1 Rear Panel 4.2 Front Panel 4.3 Top Panel 4.4 Constant Temperature Block Assembly 9011 Dual-Well Calibrator 16 Insert A Cold block insert shown (Hot block C insert includes eight 1/4" wells) 5 General Operation 5.1 Setting the Temperature 5.2 Changing Display Units Un= C 6 Controller Operation 6.1 Well Temperature 100.00C 6.2 Temperature Set-point 6.2.1 Programmable Set-points 20 SET Select Setpoint Adjust Setpoint Units C/F Scan On/Off Scan Rate Figure 4 Controller Operation Flow Chart Cold Side Only DO NOT CHANGE THESE VALUES S 6.3 Scan 6.3.1 Scan Control Sc=OFF Sc=On S 6.3.2 Scan Rate Sr=2.0 Sr=3.0 S 6.4 Temperature Display Hold 6.4.1 Switch Status 6.4.2 Scan Hold 6.5 Ramp and Soak Program Menu 20.00C S+U ProG S 6.5.1 Number of Program Set-points Pn=8 E Pf=1 Pf=4 6.5.5 Program Control P=OFF S 6.6 Set-point Resistance 99.222 6.7 Secondary Menu 6.8 Heater Power S+E SEC 12.0P 6.9 Proportional Band S+E SEC 12.0P S ProP 4.1 10.0 S 6.10 Controller Configuration 6.11 Operating Parameters PAr 6.12 High Limit S 6.13 Serial Interface Parameters Page 6.13.4 Linefeed (cold side only) LF LF=On LF=OFF 6.14 Calibration Parameters CAL Page S Page 7 Digital Communication Interface 7.1 Serial Communications 7.1.1 Wiring 7.1.2 Setup Page 7.1.3 Serial Operation 7.2 Interface Commands 40 Tabl e 2 Controller Communications Commands 41 7 Digital Communication Interface Interface Commands Controller Communications Commands continued 42 Controller Communications Commands continued 8 Test Probe Calibration 8.1 Calibrating a Single Probe 8.2 Dry-well Characteristics 8.2.1 Stabilization and Accuracy Page 9 Calibration Procedure 9.1 Calibration Procedure 9.1.1 Calibration Equipment 9.1.2 Calibration Page 10 Maintenance 11 Troubleshooting 11.1 Troubleshooting Problems, Possible Causes, and Solutions 11.2 CE Comments 11.2.1 EMC Directive 11.2.2 Low Voltage Directive (Safety)