Functions
Here, we will discuss the switches and control knobs on the front panel and Input/Output jack sockets on the rear panel. Note that some functions operate in a different ways depending on either the Dual Mode or Single Mode you set up.
Functions of the Dual Mode
EFFECT 1 VARIATION SW
Use this to choose the Variation of the Effect Type for Effect 1. There are 11 variations available on each Effect Type.
EFFECT 2 TYPE SW
Use this to choose the Effect Type for Effect 2. There are 11 types available.
EFFECT 2 ADJUST knob
This control knob adjusts the
EFFECT 1 TYPE SW
Use this to choose the Effect Type for Effect 1. There are 11 types available.
EFFECT 1 ADJUST knob
This control knob adjusts the effect parameters of Effect 1. The center position is the default setting. If you turn it to the left, the parameter will decrease. Similarly, if you turn it to the right, the parameter will increase.
EFFECT 2 VARIATION SW
Use this to choose the Variation of the Effect Type for Effect 2. There are 11 variations available on each Effect Type.
effect parameters of Effect 2. The center position is the default setting. If you turn it to the left, the parameter will decrease. Similarly, if you turn it to the right, the parameter will increase.
POWER LED
PEAK LED
EFFECT 1 |
|
|
|
|
|
|
|
|
|
|
| EFFECT 2 | This illuminates when the | |
|
|
| PARAM.1 |
|
|
|
|
|
| PARAM.2 | Power is ON.Also, this will | |||
TYPE |
|
| VARIATION | MIX |
|
| TYPE |
| VARIATION | PARAM.3 | ||||
|
| ADJUST |
|
|
| ADJUST |
| MIX |
| |||||
DLY+REV |
|
| 6 | DRY+EFF |
|
| DLY+REV |
| 6 |
| DRY+EFF | blink when the Effect | ||
VOCAL | DELAY | 5 | 7 |
|
|
| VOCAL | DELAY | 5 | 7 |
|
|
| |
PLATE | MISC | 4 | 8 |
|
|
| PLATE | MISC | 4 | 8 |
|
|
| Mute is set to ON via the |
ROOM | CHO | 3 | 9 |
| SINGLE | DUAL | ROOM | CHO | 3 | 9 |
|
|
| |
| MODE |
|
|
|
| |||||||||
S.HALL | PITCH 2 | 10 |
|
|
| S.HALL | PITCH 2 | 10 |
|
|
| Foot SW. | ||
L.HALL | FLANGE | 1 | 11 | DRY | EFF |
| L.HALL | FLANGE | 1 | 11 |
| DRY | EFF | |
|
|
|
|
|
|
|
|
|
|
|
| _ | + |
|
|
|
| PEAK |
|
|
|
|
|
| PEAK |
|
| POWER |
|
This will illuminate
MODE SW
when the Effect 1
PEAK LED
Input signal reaches
Use this to choose
This will illuminate
EFFECT 2 MIX knob
6 d B b e l o w t h e
the operation mode
when the Effect 2
Use this to adjust the mixing balance of the
distortion level.
either Dual Mode or Single Mode.
Input signal reaches 6dB below the distortion level.
Dry sound and Effect sound for the signal at the OUTPUT 2 jack sockets;
EFFECT 1 MIX knob
Use this to adjust the mixing balance of the Dry sound and Effect sound for the signal at the OUTPUT 1 jack sockets;
on the Left Max. : DRY 100%, EFF 0%
in the Center : DRY 50%, EFF 50%
on the Right Max. : DRY 0%, EFF 100%
on the Left Max. : DRY 100%, EFF 0%
in the Center : DRY 50%, EFF 50%
on the Right Max. : DRY 0%, EFF 100%
Foot SW socket
Connect a Foot SW, such as the Fostex Model 8051, to control the Effect Mute ON/ OFF.
OUTPUT 1 jack sockets
These are the output terminals used to send a processed audio signal via Effect 1 in stereo (L, R). If you want to obtain a mono audio signal, use only the OUTPUT L (MONO) jack socket.
INPUT 1 (1 & 2) jack socket
This is the input terminal used to connect the audio source for Effect 1. If you want to feed the same audio signal to both Effect 1 and Effect 2 at once, only use this socket without connecting anything into the INPUT 2 jack socket.
| EFF MUTE | R | L (MONO) | R | L (MONO) | 2 | DUAL MODE | 1 (1&2) |
|
9V |
|
|
|
|
| R | SINGLE MODE | L (MONO) |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
ONLY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MIN | MAX | MIN | MAX |
DC IN | FOOT SW |
| OUTPUT 2 |
| OUTPUT 1 |
| INPUT |
| INPUT LEVEL knobs |
|
|
|
|
|
|
| These volume knobs | |
|
|
|
|
|
|
| ||
DC INLET socket | OUTPUT 2 jack sockets |
|
| control the input level of | ||||
|
| INPUT 1 and INPUT 2. | ||||||
To connect the standard accessory |
|
| ||||||
These are the output terminals used to |
|
|
| |||||
AC adaptor to power up the |
|
|
| |||||
send a processed audio signal via Effect | INPUT 2 jack socket | |||||||
As the unit does not have a power | ||||||||
2 in stereo (L, R). If you want to obtain a | ||||||||
switch, switching the power ON is | This is the input terminal used to connect the audio | |||||||
mono audio signal, use only the | ||||||||
done by connecting the AC adaptor. | source for Effect 2. | |||||||
OUTPUT L (MONO) jack socket. | ||||||||
|
|
|
| |||||
14
