English

ASSEMBLY & OPERATION

PRIOR TO OPERATION

1.Check Power Supply

Ensure that the power source to be utilized conforms to the power source requirements specified on the tool nameplate. Ensure the receptacle being used accepts the plug tightly. If a faulty receptacle is used, it may cause overheating, resulting in a serious hazard.

2.Check Work Area

Confirm that the work site is placed under appropriate conditions conforming to precautions prescribed in the safety section of this manual.

3.Before Plugging in the Tool

Ensure that the power tool switch is in the OFF position to prevent the tool from accidental start up, which could cause serious injury.

INSTALLING AND REMOVING THE ROUTER BIT (2 Options)

WARNING: Disconnect tool from power source. Make sure the correct collet is selected to match the bit shank diameter and that the collet is securely “snapped” into the collet nut before proceeding.

(Option 1)

a)Insert the Depth Adjustment Wrench (M) into the Height Adjustment Access (L) and turn counter clockwise until the collet and collet nut (N) extend fully through the base.– Fig 1 (It may be necessary to rotate the Depth Stop Turret to the flat surface without any stops (see area marked with “X”- Fig. 11) to allow the collet to fully extend through the base.)

b)Insert the Depth Adjustment Wrench (M) into the Above Table Spindle Lock Access (R) and rotate clockwise until it stops turning. Rotate Spindle (J) until the Spindle Lock (K) pin engages. When the Spindle Lock pin is correctly engaged, you will not be able to rotate the spindle. – Fig 2

c)Using the included 22mm Collet Nut Wrench (Q), turn the collet nut counter clockwise to loosen the collet. If a bit is already in the collet the collet nut will loosen for approximately 1 turn and then become tight again. Continue turning the nut counter clockwise with the wrench until the nut is loose again. At this point the bit should be released and easy to remove from the collet– Fig 3

d)Insert the router bit and rotate the collet nut with the 22mm wrench clockwise to tighten the collet. Always be sure that at least 80% of the router bit shank is inserted in the collet but never allow the bit shank to “bottom out” in the collet. – Fig 4

e)Insert the Depth Adjustment Wrench (M) into the Above Table Spindle Lock Access (R) and rotate counter clockwise until it stops turning. – Fig 5a

f)Turn the height adjustment knob clockwise until the router bit returns fully inside the base.

Fig 5b

g)Before operating the router, follow directions in the section in this manual titled "Adjusting Depth of Cut" to properly set the depth of cut.

h)To remove a router bit from the collet, follow steps a, b, and c and then remove the router bit.

WARNING: Failure to disengage the spindle lock or remove the wrench before operating this power tool could result in injury or damage to the tool.

9

Page 10
Image 10
Freud Tools FT3000VCE operating instructions Assembly & Operation, Prior to Operation

FT3000VCE specifications

The Freud Tools FT3000VCE is an exceptional plunge router designed for both amateur woodworkers and seasoned professionals. Known for its reliability and precision, this versatile power tool stands out in the crowded market of woodworking equipment, making it a favorite among DIY enthusiasts and contractors alike.

One of the main features of the FT3000VCE is its powerful 3.0 HP motor. This robust motor provides consistent power, ensuring smooth operation even in tough materials such as hardwoods and laminates. The variable speed control, adjustable from 8,000 to 21,000 RPM, allows users to match the routing speed to the task at hand, whether it’s intricate detail work or heavy stock removal.

Precision is paramount in woodworking, and Freud addresses this with its patented "Soft Start" technology. This feature gradually ramps up the motor speed to reduce sudden jolts, giving users better control and minimizing strain on both the router and the material. Additionally, the electronic feedback system ensures a stable RPM throughout the cut, maintaining performance despite varying load conditions.

The FT3000VCE is built with user comfort in mind. Its ergonomic design includes a balanced body with soft-grip handles, allowing for easier maneuverability and reduced operator fatigue during extended use. The inclusion of a precise depth adjustment system simplifies the process of setting cut depth, while the easy-to-read scale ensures accuracy.

Another noteworthy characteristic is the dual side handles that provide added stability and control, especially during complex routing tasks. The router also features a powerful integrated dust collection system, which helps to maintain a clean working environment by effectively capturing sawdust and debris.

For versatility, the Freud FT3000VCE offers a variety of base options including a fixed base, plunge base, and even a cam-lock system for quick changes between bases. This adaptability allows woodworkers to approach a wide range of projects, from edge profiling to mortising and hollowing.

In summary, the Freud Tools FT3000VCE combines power, precision, and comfort into a single reliable tool that can elevate any woodworking project. With its advanced technologies, ergonomic design, and versatile capabilities, it remains a top choice for those seeking a high-quality plunge router.