Disassembly

2. EVAPORATOR

1.Remove the cabinet.

2.Remove the 2 screws which fasten the evaporator.

3.Move the evaporator sideways carefully.

4.After discharging the refrigerant completely, unbraze the interconnecting tube at the evaporator connections.

5.Remove the evaporator carefully.

6.Re-install the component by referring to notes. (See Figure 1)

3.CAPILLARY TUBE

1.Remove the cabinet.

2.After discharging the refrigerant completely, unbraze the interconnecting tube at the capillary tube.

3.Remove the capillary tube.

4.Re-install the component by referring to notes.

NOTICE

Replacement of the refrigeration cycle.

1.When replacing the refrigeration cycle, be sure to Discharge the refrigerant system using a FreonTM recovery System.

If there is no valve to attach the recovery system, install one (such as a WATCO A-1) before venting the FreonTM. Leave the valve in place after servicing the system.

2.After discharging the unit completely, remove the desired component, and unbraze the pinch-off tubes.

3.Solder service valves into the pinch-off tube ports, leaving the valves open.

4.Solder the pinch-off tubes with Service valves.

5.Evacuate as follows.

1)Connect the vacuum pump, as illustrated figure

14A.

2)Start the vacuum pump, slowly open manifold valves A and B with two full turns counterclock- wise and leave the valves open.

The vacuum pump is now pulling through valves A and B up to valve C by means of the manifold and entire system.

CAUTION: If high vacuum equip- ment is used, just crack valves A and B for a few minutes, then open

slowly with the two full turns counter- clockwise. This will keep oil from foaming and being drawn into the vacuum pump.

3)Operate the vacuum pump vaccum for 20 to 30 minutes, until 600 microns of vaccum is obtained. Close valves A and B, and observe vacuum gauge for a few minutes. A rise in pres- sure would indicate a possible leak or moisture

Figure 13

remaining in the system. With valves A and B closed, stop the vacuum pump.

4)Remove the hose from the vacuum pump and place it on the charging cylinder. See figure 14B. Open valve C.

Discharge the line at the manifold connection.

5)The system is now ready for final charging.

6.Recharge as follows :

1)Refrigeration cycle systems are charged from the High-side. If the total charge cannot be put in the High-side, the balance will be put in the suction line through the access valve which you installed as the system was opened.

2)Connect the charging cylinder as shown in figure 33B.

With valve C open, discharge the hose at the manifold connection.

3)Open valve A and allow the proper charge to enter the system. Valve B is still closed.

4)If more charge is required, the high-side will not take it. Close valve A.

5)With the unit running, open valve B and add the balance of the charge.

a.Do not add the liquid refrigerant to the Low-side.

b.Watch the Low-side gauge; allow pressure to rise to 39 lbs.

c.Turn off valve B and allow pressure to drop.

d.Repeat steps b. and c. until the balance of the charge is in the system.

6)When satisfied the unit is operating correctly, use the pinch-off tool with the unit still running and clamp on to the pinch-off tube. Using a tube cutter, cut the pinch-off tube about 2 inches from the pinch-off tool. Use sil-fos braze and braze pinch-off tube closed. Turn off the unit, allow it to set for a while, and then test the leakage of the pinch-off connection.

13Room Air Conditioner

Page 13
Image 13
Friedrich CP10F10, CP12F10 manual Evaporator

CP10F10, CP12F10 specifications

The Friedrich CP10F10 and CP12F10 are advanced portable air conditioning units designed to provide efficient and effective cooling solutions for both residential and commercial applications. These models stand out for their blend of performance, energy efficiency, and user-centric features.

One of the key characteristics of the Friedrich CP10F10 and CP12F10 is their robust cooling capabilities. The CP10F10 can deliver up to 10,000 BTU of cooling power, while the CP12F10 offers 12,000 BTU, making them suitable for spaces ranging from small offices to medium-sized rooms. The units are equipped with a high-efficiency rotary compressor that ensures rapid cooling while reducing energy consumption.

The cooling technology employed in these models focuses on quick temperature control and humidity reduction. Both units feature a multi-speed fan that allows users to customize airflow according to their comfort needs. This is complemented by a programmable thermostat, which enables precise temperature monitoring and adjustment, ensuring optimal indoor climate management.

In terms of design, the Friedrich CP series emphasizes portability and ease of use. Each model includes a convenient handle and durable caster wheels, allowing for effortless movement from room to room. The compact design ensures that the units can fit in various spaces without being intrusive, making them perfect for users who need flexibility.

Energy efficiency is another highlight of the CP10F10 and CP12F10. With an Energy Efficiency Ratio (EER) rating that often exceeds industry standards, these units help reduce electricity costs while maintaining effective cooling. The units utilize eco-friendly refrigerants, aligning with modern environmental standards and contributing to a smaller carbon footprint.

For user convenience, the Friedrich CP10F10 and CP12F10 are equipped with a range of features including a remote control, allowing for effortless operation from a distance. The digital display provides clear visibility of settings, and user-friendly controls make it easy to navigate through different modes such as cooling, fan, and dehumidification.

Furthermore, both models come with a built-in dehumidifier function, which is particularly useful in humid climates. This feature helps to maintain comfortable indoor air quality by reducing excess moisture, thus preventing mold growth and improving overall comfort.

In conclusion, the Friedrich CP10F10 and CP12F10 air conditioning units are ideal choices for individuals seeking reliable, portable, and energy-efficient cooling solutions. Their combination of powerful performance, innovative technologies, and user-friendly features makes them a standout option in the portable air conditioning market.