Manuals / Fujitsu / Computer Equipment / Computer Hardware

Fujitsu Annex, System board Revision and BIOS Version, D1859-A10 GS 05618476, BIOS version

Models: D1859

1 42

Download 42 pages 41.81 Kb

Page 35

Image 35

Annex

System board Revision and BIOS Version

System board Revision

The revision status of the system board exactly identifies which system board you have. It is indicated on a sticker on the edge of the system board:

D1859-A10 GS 1

05618476

Example System board revision

BIOS version

The BIOS version can be displayed in the BIOS Setup.

►Press F2 during booting to open the BIOS Setup.

►Press F1 .

The BIOS version is specified on the displayed information page under the entry BIOS Release.

D1859 (Econel 50)

Page 35

Image 35

Fujitsu technical manual Annex, System board Revision and BIOS Version, D1859-A10 GS 05618476, BIOS version

Contents

Technical manual Englishreliability2 System board D1859 EconelAre there Right of technical modification reserved This manual was produced by Offenders will be liable for damagesPage Add-on modules / Upgrading ContentsJumper settings D1859 EconelPage Additional information System board D1859Notational conventions Important notes Important notesInformation about boards Special onboard features List of featuresList of features Onboard featuresExternal ports List of featuresInternal ports continued D1859-ABrief instructions on installing system board Brief instructions on installing system boardPrior to installation InstallationBrief instructions on installing system board Driver installationATX power 4pin PWR2 Interfaces and connectorsExternal ports LAN connectorExternal ports Internal ports and connectors Internal ports and connectorsHard disk connection Pin assignment of internal ports Pin assignment of internal portsFront panel Serial ATAPin assignment of internal ports IDE/ATA interfacePin assignment of internal ports USB - dual channelSide 1 Select low Floppy interfacePin assignment of internal ports Pin assignment of internal ports LCD displayIntrusion Pin assignment of internal ports Power supply BTXAdditional power supply ATX12 Pin assignment of internal ports Power supply controlRecovering System BIOS - pinpair B Jumper settingsSetting via control-panel plug connector Skipping system and BIOS Setup password - pinpair ATechnical data Installing and removing processorsInstalling processor with heat sink Add-on modules / UpgradingD1859 Econel Add-on modules / UpgradingFold down the frame Press the lever downward 2 until it is hooked in againUse only the heat sink supplied with your system Mounting heat sinkAdd-on modules / Upgrading Channel B Upgrading main memoryTechnical data Add-on modules / UpgradingRemoving a memory module Installing a memory moduleAdd-on modules / Upgrading Add-on modules / Upgrading Adding PCI Express cardsAdding PCI cards PCI bus interrupts - Selecting correct PCI slotPCI Slot Add-on modules / UpgradingOn board controller Slot PCIAdd-on modules / Upgrading Replacing the lithium batteryAdd-on modules / Upgrading BIOS updateWhen should a BIOS update be carried out? Where can I obtain BIOS updates?Add-on modules / Upgrading BIOS Recovery - Recovering System BIOSAll BIOS settings are reset to the default values When should a microcode update be carried out? Microcode UpdateWhat is a microcode update? Safety for processor on Fujitsu Siemens Computers system boardsD1859-A10 GS 05618476 System board Revision and BIOS VersionAnnex BIOS versionLoadability for connections and fuses Electrical PropertiesAnnex flashbio++/p6 Error messagesError messages DMA test failed EISA CMOS not writable Error messagesKeyboard error nn nn Stuck Key Error messagesUncorrectable ECC DRAM error DRAM Parity error Unknown PCI error Error messagesSystem Management Configuration changed or Problem occurred System timer errorGlossary http//ts.fujitsu.com Information on this documentHinweise zum vorliegenden Dokument