Fujitsu FI-4860C AP-12

<Power supply alarm>	The following message is displayed, when an error occurs in the Power sup-
	ply.
	P o w e r			s u p p l y
	e	r	r	o	r
<EEPROM alarm>	The following message is displayed, when an error occurs in the EEPROM.
	A D D R	E	S	S	x x H
	E E P R O M				A l a r m

HINT

The EEPROM address where the error occurs is indicated by [xx] digits in the above shown screen.

<VDCC Read/Write	The following message is displayed, if an error occurs when accessing the
alarm>	VDCC area.
	V D C C 2	R / W	E r r o r
(MDC timeout)	The following message is displayed, if an error occurs when accessing the
	MDC area.

M D C T i m e o u t

The following message is displayed, if an error occurs when accessing the Dither/Gamma RAM.

D i t h e r / G a m m a

R / W E r r o r

<Temporary	The following message is displayed, if an error occurs during accessing the
memory Read/Write	temporary memory.
alarm>
	T e m p M e m	R / W e r r o r

AP-12

Contents

fi-4860CImage Scanner Page INTRODUCTION High speed, high quality color scanning capabilities Highly reliable document handling Production ready About this manual ●ii ●iii ●iv Use in High-safetyApplications About the use of mercury Illegal Copying Copyrighted Material ●vi ●vii ●viii ●ix About Maintenance WARNING Do not touch the AC cable with wet hands Do not damage the AC cable Use only specified AC cables and connector cables ●xi ●xii ●xiii ●xiv ●xv ●xvi ●xvii ●xviii CONTENTS ●xx Page 1.1Checking the Contents of the Scanner Package 1.2 Names and Functions of Parts No Name Function Page 1.3Operator Panel Button LCD Page Counter Functions Installing the Scanner Connecting the Scanner Installing the Scanner Driver and Application 2.1 Installing the Scanner 2.2 Connecting the Scanner Page Product/ASC-29160&filekey=u160_winxp_drv_rc1.exe (Back side) 2.Connect and secure the other end of the interface cable to the PC 2-16 2.2 Connecting the Scanner 2.3Installing the Scanner Driver and Application For Windows 98, Windows Me, Windows 2000, and Windows XP: FUJITSU TWAIN32 For Windows 95: •When using Windows 95: 1.Turn on the scanner 2.Turn on your PC and log on to Windows Click [Cancel] to close the Wizard window 4.Insert the Setup CD-ROMinto the CD drive ⇒<SETUP DISK START UP SCREEN> appears 5.Click [INSTALL PRODUCTS] Page 8.Install the application following the instructions in the window 9.When the [InstallShield Wiizard Complete] window appears, click [Finish] Now the installation of the scanner driver is completed 1.Insert the Setup CD-ROMinto the CD drive 2.Click [INSTALL PRODUCTS] 3.Click [ScandAll 21] on the window below Page 1.Set documents on the Hopper 2.Start ScandAll21 3.Specify the scanner to use Page Page For FUJITSU ISIS Scanner Driver Page 4.Insert the "Setup CD-ROM"into the CD drive Page 8.Install the application following the instructions on the window ⇒<SETUP DISK STARTUP SCREEN> appears 2.Click [INSTALL PRODUCTS] Page 5.Enter required information, then click [Next >] button 6.Install the application following the instructions on the window Page 4.Load the documents on the Hopper 6.Select [Preview Scan] from the [Scan] menu. And then the document is scanned Adobe® Acrobat® 1.Insert the Adobe Acrobat 5.0 CD-ROMinto the CD-ROMdrive 2.The following window appears. Click the [Next] button Page ⇒The Setup window appears and the installation will be started APPENDIX-1MESSAGES OF OPERATOR PANEL AP-1 AP-2 AP-3 AP-4 AP-5 AP-6 AP-7 AP-8 AP-9 AP-10 AP-11 AP-12 AP-13 APPENDIX-2CONSUMABLES AND REPLACEMENT CYCLE AP-14 APPENDIX-3TROUBLESHOOTING AP-15 AP-16 APPENDIX-4CLEARING DOCUMENT JAMS AP-17 AP-18 AP-19 AP-20 AP-21 AP-22 ●IN-1 ●IN-2 fi-4860CImage Scanner Installation Guide P3PC-E177-04EN Printed in Japan