Fujitsu M4000, M5000 1.3.3 Memory Board

Chapter 1 System Overview 1-13

FIGURE1-8 CPU Modules in the M5000 Server

1.3.3 Memory Board

Each memory board provides a memory access controller(MAC) and eight DIMM

slots (FIGURE1-9 and FIGURE1-10). To remove or install memory boards, you must

power the server off. TABLE1-5 lists the memory board features.

Toinstall DIMMs, you must remove the memory board and open the case of the

memory board. The servers use Double Data Rate II (DDR-II) type memory with the

following features:

■Error Checking and Correction (ECC) error protection

■Recovery from memory chip failures

FIGURE1-9 and FIGURE1-10 illustrate the location of the memory boards in both

midrange servers.

TABLE1-5 Memory Board Features

Location Topof server

Cold FRU replacement capability Yes

Contents

Main Please Recycle Page Page Contents Page Page Page Preface SPARC Enterprise M4000/M5000 Servers Documentation Note Page Text Conventions Notes on Safety Documentation Feedback System Overview 1.1 Product Overview 1.2 Features Page Note 1.2.1 SPARC Enterprise M4000 Server Page 1.2.2 SPARC Enterprise M5000 Server 1.2.3 Operator Panel Overview 1.3 Components 1.3.1 Motherboard Unit 1.3.2 CPU Module Page 1.3.3 Memory Board Page 1.3.4 Fan Unit Page 1.3.5 Power Supply Page CPU Types and Server Maximum PowerConsumption Note 1.3.6 Operator Panel Page Page 1.3.7 eXtended System Control Facility Unit (XSCFU) Page Page 1.3.8 I/O Unit Page 1.3.9 On-Board Drive Units Page 1.3.9.1 CD-RW/DVD-RW Drive Unit Caution Note 1.3.9.2 Hard Disk Drive 1.3.9.3 Tape Drive Unit 1.4 I/O Options 1.4.1 External I/O Expansion Unit 1.4.2 PCI Cards 1.5 Software Features System Features and Capabilities 2.1 Hardware Configuration 2.1.1 CPU Module 2.1.1.1 CPU Types and Features 2.1.1.2 Supported Processors and CPU Operational Modes Note 2.1.2 Memory Subsystem 2.1.3 I/O Subsystem 2.1.4 System Bus 2.1.5 System Control 2.1.5.1 eXtended System Control Facility Unit (XSCFU) 2.1.5.2 Fault Detection and Management 2.1.5.3 System Remote Control/Monitoring 2.2 Partitioning 2.2.1 Physical Unit for Domain Constitution 2.2.2 Domain Configuration 2.3 Resource Management 2.3.1 Dynamic Reconfiguration 2.3.2 PCI Hot-Plug 2.3.3 Capacity on Demand (COD) 2.3.4 Zones 2.4 Reliability,Availability, and Serviceability 2.4.1 Reliability 2.4.2 Availability 2.4.3 Serviceability About the Software 3.1 Oracle Solaris Operating System Software 3.1.1 Domains 3.1.2 PCI Hot-Plug 3.2 XSCF Firmware 3.2.1 XSCF User Interfaces 3.2.2 XSCF Features 3.2.2.1 System Management 3.2.2.2 Security Management 3.2.3 System Status Management 3.2.3.1 Error Detection and Management 3.2.3.2 Remote Control and Monitoring 3.2.3.3 Configuration Management 3.2.3.4 Airflow Indicator Note Page Index C D E F