Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MAW3147NC/NP, MAW3300NC/NP, MAW3073NC/NP External operator panel on NP model drives only

Models: MAW3147NC/NP MAW3073NC/NP MAW3300NC/NP

1 130

Page 71

4.3.4External operator panel (on NP model drives only)

(4)External operator panel (NP model only)

The external operator panel is installed only when required for the system. When connection is not required, leave open the following pins in the external operator panel connector of the HDD: Pins 21, 22 and pins 01 through 08 in CN2 and pins A1 through A12 in CN1.

4.3.4External operator panel (on NP model drives only)

A recommended circuit of the external operator panel is shown in Figure 4.23. Since the external operator panel is not provided as an option, this panel must be fabricated at the user site referring to the recommendation if necessary.

(HDD)

C N 1

(*1)

A10

A11

-ID0

-ID1

-ID2

-ID3

GND


-LED			(LED)


+5V
+5V		R




	Approx. 300Ω

LED (+5V)

-LED

(LED)

ID0

ID1

ID2

ID3

(for 16-bit SCSI)

(*1) For connecting the external LED to CN2.

Figure 4.23 External operator panel circuit example

C141-E226

4-21

Page 71

Image 71

Fujitsu MAW3147NC/NP manual External operator panel on NP model drives only, 23 External operator panel circuit example

Contents

MAW3300NC/NP MAW3147NC/NP MAW3073NC/NP HARD DISK DRIVES C141-E226-01ENPRODUCT/MAINTENANCE MANUAL IMPORTANT NOTE TO USERS FOR SAFE OPERATIONHandling of This manual Specification No. C141-E226-**EN REVISION RECORDRelated Standards CHAPTER 6 DIAGNOSTICS AND MAINTENANCE CHAPTER 2 SPECIFICATIONSCHAPTER 4 INSTALLATION REQUIREMENTS CHAPTER 5 INSTALLATIONNever remove any labels from the drive or deface them in any way CONVENTIONS USED IN THIS MANUALCONVENTIONS FOR ALERT MESSAGES DamageImportant Alert Messages Important Alert ItemsTask Installation MAINTENANCESpecifications Installation RequirementsThis page is intentionally left blank CHAPTER CONTENTSSPECIFICATIONS INSTALLATION REQUIREMENTSCHAPTER 6 DIAGNOSTICS AND MAINTENANCE CHAPTER 5 INSTALLATIONIN-1 APPENDIX A SETTING TERMINALSAPPENDIX B CONNECTOR SIGNAL ALLOCATION INDEXFIGURES Test flowchart Output signal for external LEDSetting terminals location on NP models only CN2 setting terminal on NP models onlyTABLES CHAPTER 1 GENERAL DESCRIPTION 1.1 Standard Features 1.2 Hardware Structure 1.3 System Configuration1.1 Standard Features The continuous processing up to 64K-1 blocks in a command can be achieved, and the HDD can perform continuous read/write operation when processing data blocks on several tracks or cylinder Error rate increase 16 Large capacity 19 Low power consumption14 Defective block slipping 15 High speed positioningC141-E226 1.2 Hardware StructureFigure 1.1 NC model drives outer view Figure 1.2 NP model drives outer view4 Actuator 1 Disks2 Heads 3 Spindle motorC141-E226 1.3 System ConfigurationFigure 1.3 System configuration SCSI bus HDD HDD #14 #15SCSI ID 1 SCSI bus configuration16-bit SCSISelectable from 0 to 15 switch selectable 2 Addressing of peripheral deviceThis page is intentionally left blank Table 2.1 Model names and order numbers CHAPTER 2 SPECIFICATIONS2.1 Hardware Specifications 2.2 SCSI Function Specifications 2.1 Hardware Specifications 2.1.1 Model name and order numberSeek time *3 2.1.2 Function specificationsFunction specifications Track to Track1 on 1 connection case transmission characteristics. 1MB/s=1,000,000 bytes/s2 1GB=1,000,000,000 bytes 3 The seek time is as follows Seek time ms Seek Difference 4096 Cyl/divEnvironmental/power requirements 2.1.3 Environmental specifications2.1.5 Reliability 2.1.4 Error rateDE surface temperature 46C to 50C 3 Service lifeDE surface temperature 40C or less DE surface temperature 41C to 45C4 Refer to 12 of Section 2.2 SCSI Function SpecificationsSCSI function specifications This page is intentionally left blank 3.3 Defect Management 3.1.1 Cylinder configurationCHAPTER 3 DATA FORMAT 3.1 Data Space 3.2 Logical Data Block AddressingFigure 3.1 Cylinder configuration 3.1.2 Alternate spare area Figure 3.3 Alternate cylinder Figure 3.2 Spare area in cellServo frame 3.1.3 Track formatFigure 3.4 Track format Track skew Head Track skew Head skew Head Figure 3.5 Track skew/head skew3.1.4 Sector format Figure 3.6 Sector format5 BCRC 1 Gaps G1, G2, G3 No pattern is written on the gap field 2 PLO Sync3 Sync Mark SM1, SM2 4 Data field DATA1-DATA4Model 3.1.5 Format capacityFormat capacity 3.2 Logical Data Block AddressingC141-E226 1 Block address of user space2 Alternate area 3.3.2 Alternate block allocation 3.3 Defect Management 3.3.1 Defect list3-11 1 Alternate block allocation during FORMAT UNIT command executionC141-E226 Figure 3.7 Alternate block allocation by FORMAT UNIT command Example Reassign Block Figure 3.8 Alternate block allocation by REASSIGN BLOCKS commandType 2 Reassignment of write fail sector 1 Commands to be applied Type 1 Reassignment of Uncorrectable Read Error1 Commands to be applied WRITE WRITE EXTEND c SA and defect map update processing on alternate sideARRE = Twice AWRE Type 1 = Eight times This page is intentionally left blank 4.3 Connection Requirements CHAPTER 4 INSTALLATION REQUIREMENTS4.1 Mounting Requirements 4.2 Power Supply Requirements 4.1 Mounting Requirements 4.1.1 External dimensionsC141-E226 Figure 4.1 NC model dimensionsUnit mm C141-E226 Figure 4.2 NP model dimensionsUnit mm Figure 4.3 HDD orientations 4.1.3 Notes on mounting 4.1.2 Mounting orientations5.0 or less 5.0 or less Figure 4.4 Mounting frame structurepackage Table 4.1 Surface temperature check pointFigure 4.5 Limitation of side-mounting Figure 4.7 Service clearance area Figure 4.6 Surface temperature measurement pointsMAW3300NC/NP 4.2 Power Supply RequirementsFigure 4.9 Power on/off sequence Figure 4.8 Spin-up current waveform +12V DCSCSI devices without noise leaking designed Figure 4.10 Power on/off sequenceFigure 4.11 Power on/off sequence SCSI devices with the terminating resistorSCSI ID Delay time of spindle motor starting5 Power supply to SCSI terminating resistor 4 Sequential starting of spindle motors1 Connectors 4.3.1 SCA2 connector type 16-bit SCSI model NC modelFigure 4.13 NC connectors location Figure 4.12 AC noise filter recommended 4.3 Connection RequirementsFigure 4.14 SCA2 type 16-bit SCSI connector Figure 4.15 NP connectors and terminals location 4.3.2 68-pin connector type 16-bit SCSI model NP modelFigure 4.17 Power supply connector 68-pin type 16-bit SCSI Figure 4.16 68-pin type 16-bit SCSI interface connectorFigure 4.19 External operator panel connector CN2 Figure 4.18 External operator panel connector CN1C141-E226 Figure 4.20 16-bit SCSI ID external input5 External operator panel connector Signals 4-16This signal is temporarily driven at the GND level when the micro program reads the SCSI ID immediately after the power supply to the HDD has been switched on it is possible to set up the SCSI ID by short circuiting CN1-A1 and CN1-A2 C141-E226 Figure 4.21 Output signal for external LEDe. -WTP Input signal CN1-A12 and CN2-9, 10 pin 4-18C141-E226 Figure 4.22 SCSI cables connection6 Cable connection requirements External operator panel exampleTable 4.2 Recommended components for connection 4.3.3 Cable connector requirementsFigure 4.23 External operator panel circuit example 4.3.4 External operator panel on NP model drives onlyC141-E226 4-225.6 Confirming Operations after Installation and Preparation for Use CHAPTER 5 INSTALLATION5.1 Notes on Handling Drives 5.2 Connections 5.3 Setting Terminals 5.4 Mounting Drives 5.5 Connecting Cables2 Unpackaging 3 Installation/removal/replacementd Keep a record of all maintenance work for replacing 4 Packaging c To prevent condensation, avoid sudden changes in temperature5.2 Connections 3 Connecting two drives or more multi-host HDD HDD SCSI terminator Figure 5.1 SCSI bus connections 1 ofFigure 5.1 SCSI bus connections 2 of 2 Connecting two drives or more single host HDD HDDFigure 5.2 Setting terminals location on NP models only 5.3 Setting Terminals5.3.1 SCSI ID setting Figure 5.3 CN2 setting terminal on NP models onlySCSI ID setting Supply on 5.3.2 Each mode settingTable 5.2 Setting SCSI terminator power supply NP model Table 5.3 Motor start mode settingTable 5.6 Setting the bus width of the SCSI interface NP model Table 5.4 Write protect setting NP modelTable 5.5 Setting of the SCSI interface operation mode NP model Table 5.7 Default mode settings by CHANGE DEFINITION command 5.3.3 Mode settings5.4 Mounting Drives 5.4.1 Check before mounting Setting check list NP model only5.4.2 Mounting procedures 5.5 Connecting Cables 5.6 Confirming Operations after Installation and Preparation for Use 5.6.1 Confirming initial operationsRemark 5.6.2 Checking SCSI connection Unit Of =1 Figure 5.4 Checking the SCSI connection AMotor starts when power is turned on Self test =C141-E226 Figure 5.5 Checking the SCSI connection BMotor starts by START/STOP command Executing time about 60 seconds 5-165.6.3 Formatting b. Format parameter 2 FORMAT UNIT commandb. Format parameter page code = a. Specifying CDB5.6.4 Setting parameters continued 2 Disconnection/reconnection parameters page code = Default valueAverage amount of processing data specified with a command ARRE AWRE TB PERabsolute value control pagesequence of 5.7 Dismounting Drives5.8 Spare Disk Drive This page is intentionally left blank 6.1 Diagnostics 6.1.1 Self-diagnostics CHAPTER 6 DIAGNOSTICS AND MAINTENANCE6.1 Diagnostics 6.2 Maintenance Information 6.3 Operation Check 6.4 Troubleshooting ProceduresRAM microcode is stored Peripheral circuits of microprocessor MPU Brief test contents of self-diagnostics are as follows1 Initial self-diagnostics a. Hardware function testOperation of self-diagnostics 6.1.2 Test programs 6.2 Maintenance Information 6.2.1 Precautions 6.2.2 Maintenance requirements 6.2.3 Maintenance levels Figure 6.1 Revision label example 6.2.4 Revision numbersRevising at field Figure 6.2 Indicating revision numbers 6.2.5 Tools and test equipment6.2.6 Tests Figure 6.3 Test flowchart 6.3.2 Operation test 6.3.3 Diagnostic test6.3 Operation Check 6.3.1 Initial seek operation check 6.4 Troubleshooting Procedures 6.4.1 Outline of troubleshooting procedures6.4.2 Troubleshooting with disk drive replacement in the field System-level field troubleshooting Damage 1. Never remove any labels from the drive 6.4.3 Troubleshooting at the repair siteDisk drive troubleshooting C141-E226 6.4.4 Troubleshooting with parts replacement in the factory6.4.5 Finding possibly faulty parts This manual does not cover troubleshooting at the factory levelThis page is intentionally left blank 7.1 Error Analysis Information Collection 7.1.1 Sense data CHAPTER 7 ERROR ANALYSIS7.1 Error Analysis Information Collection 7.2 Sense Data Analysis Additional sense code qualifier Figure 7.1 Format of extended sense dataAdditional sense code Sense 7.2.1 Error information indicated with sense data7.2 Sense Data Analysis Table 7.1 Definition of sense data7.2.2 Sense data 3-0C-03, 4-40-xx, and 4-C4-xx 7.2.3 Sense data 1-1x-xx, 3-1x-xx and E-1D-00 Disk read errorA.1 Setting Terminals on NP model only APPENDIX A SETTING TERMINALSMotor start mode CN2 setting terminal on NP model drives onlyTable A.1 A.1 Setting Terminals on NP model onlyB.2 SCSI Connector Signal Allocation 68-pin type LVD 16-bit SCSI APPENDIX B CONNECTOR SIGNAL ALLOCATIONB.1 SCSI Connector Signal Allocation SCA2 type LVD 16-bit SCSI C141-E226 Table B.1 SCSI connector SCA2 type LVD 16-bit SCSI CN1B.1 SCSI Connector Signal Allocation SCA2 type LVD 16-bit SCSI Table B.2 SCSI connector 68-pin type LVD 16-bit SCSI CN1 SCSI Connector Signal Allocation 68-pin type LVD 16-bit SCSIThis page is intentionally left blank INDEX Page Page This page is intentionally left blank Comment Form This page is intentionally left blankw