Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MPC3032AT manual Preface, Maintenance And Diagnostic, Removal And Replacement Procedure

Models: MPC3064AT MPC3032AT MPC3043AT MPC3084AT MPC3102AT MPC3096AT

1 31

Download 31 pages 266 b

Page 4

PREFACE

This manual describes the MPC3032AT, MPC3043AT, MPC3064AT, MPC3084AT, MPC3096AT and MPC3102AT a 3.5-inch hard disk drive with a BUILT-IN controller that is compatible with the IBM PC-AT interface.

This manual explains, in detail, how to maintenance the disk drives.

This manual assumes that users have a basic knowledge of hard disk drives and their application in computer systems.

This manual consists of the following two chapters:

Chapter 1 MAINTENANCE AND DIAGNOSTIC

Chapter 2 REMOVAL AND REPLACEMENT PROCEDURE

In this manual, disk drives may be referred to as drives, or devices.

IBM PC-AT is a registered trademark of IBM (International Business Machines Corporation) of the United States of America.

C141-F029-02EN

iii

Image 4

Fujitsu MPC3032AT, MPC3096AT, MPC3102AT, MPC3084AT Preface, Maintenance And Diagnostic, Removal And Replacement Procedure

Contents

MPC3032AT MPC3043AT MPC3064AT MPC3084AT MPC3096AT MPC3102AT DISK DRIVES MAINTENANCE MANUALC141-F029-02EN Revised contents REVISION RECORDApril EditionThis page is intentinally left blank Chapter 2 REMOVAL AND REPLACEMENT PROCEDURE Chapter 1 MAINTENANCE AND DIAGNOSTICPREFACE Conventions for Alert Messages The DE is completely sealed. Do not open the DE in the fieldLIABILITY EXCEPTION C141-F029-01ENThis page is intentinally left blank Dont install or remove a PCA or connect or disconnect a cable or connector plug when the drive is powered. ThisAvoid dangerous detergents when cleaning the disk drive be unpredictable. Only power the drive with all boardsPerform any removal after the system power is completely power ONabout 30 s after the power is turned OFF disconnected. The cable must not be disconnected and theCONTENTS CHAPTER 2 REMOVAL AND REPLACEMENT PROCEDUREThis page is intentionally left blank FIGURES TABLESThis page is intentinally left blank CHAPTER 1 MAINTENANCE AND DIAGNOSIS 1.1 Maintenance 1.2 Operation Confirmation1.3 Troubleshooting Procedure 1.1 Maintenance 1.1.1 Rules for maintenance5. Keep all vents open opened and unblocked 1.1.2 Maintenance requirementsThe DE is completely sealed. Do not open the DE in the field Page c. Installation b. Unpackingd Never ever remove the DE seal label and screws and the DE cover d. Packaging1.1.4 Disk drive revision number 1.1.3 Maintenance levelsFigure 1.1 Disk drive revision number label Figure 1.2 Display of disk drive revision number 1.1.5 Tools and test equipment 1.1.6 Self-diagnostics1.1.7 Test Figure 1.3 Test flowchart Table 1.2 Disposition for error register contents Table 1.1 Status register contents1.2 Operation Confirmation 1.2.1 Operation test 1.3 Troubleshooting Procedure 1.3.1 Troubleshooting procedure 1.2.2 Diagnostic test1.3.2 Troubleshooting disk drive replaced in field Table 1.3 System level and field troubleshooting 1.3.3 Troubleshooting at factory 2.1 Spare Parts 2.2 Disk Drive Removal CHAPTER 2 REMOVAL AND REPLACEMENT PROCEDURE2.1 Spare Parts Table 2.1 Model and parts numbers 2.2 Disk Drive RemovalThis page is intentinally left blank I, Place des Etas-Unis, SILIC 310, 94588 Rungis Cedex, FRANCE FUJITSU LIMITED Reader Comment Form