FUNAI CDV210HH8 owner manual Quick Use Guide, Connections, Press B to start Auto Set Up

Quick Use Guide

1Connections

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [SOURCE] on the unit so that the VCR SOURCE light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, press and hold [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4.

6)Press [STOP C] to stop playback.

2Installing the Batteries for the Remote Control

1 2 3

3VCR/DVD Switching

here			1	2	3	OPEN/CLOSE
			STANDBY-ON	SPEED	AUDIO	/EJECT
cut				0	+10	SKIP/CH.
			4
				5	6
						VCR/TV
			7	8	9
		VCR button				SLOW
			DISPLAY	VCR	DVD	PAUSE
		DVD button		PLAY
		SOURCE button
VCR	DVD			STOP
			RECORD
			MENU		ENTER
			SETUP	TOP MENU		RETURN
	SOURCE
		DVD SOURCE light	MODE	ZOOM	SEARCH	CLEAR/
					MODE	C. RESET
			T-SET	ANGLE	REPEAT	A-B
			SUBTITLE
		VCR SOURCE light

VCR MODE

Press [VCR] on the remote control. (Verify that the VCR SOURCE light is lit.)

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD SOURCE light is lit.)

Hint

•Pressing only [SOURCE] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

4Turn on the Unit for the First Time

VCR

1Turn on the TV and set it to channel 3.

•If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section.

2Select your language when turning this unit on for the first time. Then press [B] to go to next step.

	LANGUAGE SELECT
STANDBY-ON	B ENGLISH	[ON]
	FRANCAIS
	ESPAÑOL

or

3	Press [B] to start Auto Set Up.	CH 01
		AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES NO

Yes Press [MENU] to exit.

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable con- nections. Then, press [B] once again.

5Clock Setup

VCR

1 Press [MENU] and select “CLOCK SET“.	- M E N U -
Then press [B] to go to next step.	TIMER PROGRAMMING
	AUTO REPEAT [OFF]
MENU	CHANNEL SET UP
	B CLOCK SET
	LANGUAGE SELECT

or

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2.

2	Select the current month.	MONTH DAY			YEAR
				CLOCK SET
	Then press [B] to go to next step.	1 0	/	– –	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
3	Select the current day.			CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 1	– – – –
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
4	Select the current year.	MONTH DAY			YEAR
				CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 1	2 0 0 7
		HOUR MINUTE			AM/PM
	or	– –	:	– –	– –
5	Select the current hour.			CLOCK SET
	Then press [B] to go to next step.	MONTH DAY			YEAR
		1 0	/	0 1 MON	2 0 0 7
		HOUR MINUTE			AM/PM
	or	0 5	:	– –	– –
6	Select the current minute.	MONTH DAY			YEAR
				CLOCK SET
	Then press [B] to go to next step.	1 0	/	0 1 MON	2 0 0 7
		HOUR MINUTE			AM/PM
	or	0 5	:	4 0	– –
7	Select “AM” or “PM”.			CLOCK SET
		MONTH DAY			YEAR
		1 0	/	0 1 MON	2 0 0 7
	or	HOUR MINUTE			AM/PM
		0 5	:	4 0	P M AM

B PM

8To exit the CLOCK SET screen

– 25 – EN

E8C1UCD_EN.indd 25 2007/04/03 9:49:34