FUNAI CR320IL8 A owner manual Initial Setting, 5Initial Setup, 5Main Menu

INITIAL SETTING

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

5Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and “AUTO PRESET CH”, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure if the unit is connected to antenna or cable.

1After making all the necessary connections, press [POWER] to turn on the unit.

POWER

• This operation may take a few moments.

2Use [CH K/L] or [VOL X] to select the on-screen language from the choices on the left side of the TV screen. (ENGLISH / ESPAÑOL / FRANÇAIS)

CH	SELECT LANGUAGE
or
	ENGLISH
CH	NEXT:PRESS CHK
	ESPAÑOL
or	DESPUÉS:PRESIONE CHL
	FRANÇAIS
VOL	APRÈS:PRESSEZ VOLX

•Press [CH K] for English.

•Press [CH L] for Spanish.

•Press [VOL X] for French.

3Use [CH K/L] to select “AUTO PRESET CH(TV/DTV)” for TV channels or “AUTO PRESET CH(CATV)“ for CATV channels, then press [VOL X].

CH	- INITIAL SETUP -
or
	1. PLEASE CONNECT ANTENNA TO
CH	THE UNIT.
	2. SET UP THE ITEMS WITH
	, AND BUTTONS.
	AUTO PRESET CH (TV/DTV)
	AUTO PRESET CH (CATV)

VOL

•Scanning and memorizing the channels automatically start.

25

AUTO PRESET CH(TV/DTV)

•When the scanning and memorizing are completed, the lowest memorized channel in the broadcasting will be displayed.

10

Note:

•If you connect the cable system directly, contact the CATV installer.

•If you press [POWER] or [MENU] during “AUTO PRESET CH”, this setting will be canceled.

•The initial auto channel scan function can be executed for either TV/DTV or CATV only once. If you want to scan both TV/DTV and CATV, you need to select “CHANNEL SETUP” in the main menu to scan and memorize other channels after initial presetting is completed. (Refer to page 11.)

•You can cancel or exit the initial “AUTO PRESET CH” menu by pressing [MENU].

•When no channel can be received by “AUTO PRESET CH”, “NO TV SIGNALS” is displayed on the TV screen.

•If there is no signal input from the antenna terminal and no operation for more than few seconds, “HELPFUL HINTS” appears. Follow the instructions listed on the TV screen.

-HELPFUL HINTS -

1.PLEASE CHECK TO SEE IF THE ANTENNA/CABLE/SATELLITE IS PROPERLY CONNECTED.

2.DID YOU PERFORM “AUTO PRESET CH”?

3.PLEASE REFER TO FRONT PAGE OF THE OWNER’S MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION.

5Main Menu

This section describes the overview of the main menu displayed when you press [MENU].

For more details, see the reference page for each item.

The main menu consists of the function setting items below.

Press [MENU].

e.g.) digital TV mode

	- TV SETUP -
	PICTURE
	CHANNEL SETUP
MENU	V-CHIP	SETUP
	LANGUAGE [ENGLISH]
	CAPTION	[OFF]
	DTV SETUP

• PICTURE

You can adjust the picture quality.

(Refer to “Picture Adjustment” on page 17.)

• CHANNEL SETUP

You can automatically scan the viewable channels and remove those that are undesired.

(Refer to “Auto Channel Scan” on page 11.)

•V-CHIP SETUP

You can set the viewing limitations. (Refer to “V-chip” on page 20.)

•LANGUAGE

You can change the language (English, Spanish, French) displayed on the main menu.

(Refer to “Language Selection” on page 11.)

• CAPTION

You can change the display format for closed caption, which displays the dialogue of a TV program or other information across the TV screen.

(Refer to “Closed Caption” on page 17.)

• DTV SETUP

You can set the screen display or caption in the DTV mode.

(Refer to “DTV Closed Caption” on page 18.)

EN