AUTOMATIC CLOCK SETTING
Make sure ...
• The TV/VCR is turned on. |
• Confirm the TV/VCR is receiving a RF (Radio |
Frequency) signal from either an antenna or cable |
system connection using the ANT IN jack on the |
NOTE:During Auto Clock CH Search, the picture may be distorted. This is normal.
4Enter the channel number that contains the Automatic Clock Setting Signal
rear of the TV/VCR. |
NOTE:
• If a cable converter box is being used, make sure it |
is powered on. |
• You must use the TV/VCR remote control to per- |
form the clock setting procedure. |
• If the TV/VCR is connected directly to a cable con- |
verter box or satellite box, the local PBS station |
must be selected on the cable box itself, and the |
TV/VCR must be set to the output channel of the |
cable converter box or satellite box (usually chan- |
nel 3 or 4), to be able to set up or correct the clock |
automatically. |
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L button to select “SETTING CLOCK”.
Press the F.FWD/B button to enter “SETTING CLOCK” menu.
Press the STOP/L button to select “AUTO CLOCK CH”.
Press the F.FWD/B or REW/s buttons until you locate Auto Clock Set station number. See item 3 above.
– M E N U –
TIMER PROGRAMMING PICTURE CONTROL
BSETTING CLOCK CHANNEL SET UP USER’S SET UP
TIME SEARCH
– SETTING CLOCK –
AUTO CLOCK | [ON] |
AUTO CLOCK CH SEARCH | |
B AUTO CLOCK CH | [ 45] |
MANUAL CLOCK SET |
|
D.S.T. | [OFF] |
Press the MENU button to exit the screen.
1Select “SETTING CLOCK”
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L but- ton to select “SETTING CLOCK”. Press the F.FWD/B button to enter “SETTING CLOCK” menu.
– M E N U –
TIMER PROGRAMMING PICTURE CONTROL
BSETTING CLOCK CHANNEL SET UP USER’S SET UP
TIME SEARCH
5Turn off the TV/VCR
Once the TV/VCR is turned off , it will periodically check and set the correct date and time.
CHANNEL SET UP AGAIN
Make sure ...
2 Set “AUTO CLOCK” to [ON] | – SETTING CLOCK – |
Press the F.FWD/B button until | B AUTO CLOCK [ON] |
•Press the POWER button to turn on the TV/VCR.
AUTO CLOCK [ON] appears. | AUTO CLOCK CH SEARCH | |
AUTO CLOCK CH | [ 02 ] | |
MANUAL CLOCK SET |
| |
| D.S.T. | [OFF] |
3Begin “AUTO CLOCK CH SEARCH”
Press the STOP/L button to select “AUTO CLOCK CH SEARCH”.
1Select “CHANNEL SET UP”
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L but- ton to point to “CHANNEL SET UP”.
Then, press the F.FWD/B button.
– M E N U –
TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK
BCHANNEL SET UP USER’S SET UP
TIME SEARCH
Press the F.FWD/B button. | AUTO CLOCK | [ON] |
• The TV/VCR is now searching | B AUTO CLOCK CH SEARCH | |
AUTO CLOCK CH | [ 02 ] | |
D.S.T. | [OFF] | |
| MANUAL CLOCK SET |
|
for the station which contain the auto clock set signal. The search for a signal may take up to 20 seconds per channel.
2Begin auto preset
Press the PLAY/K or STOP/L but- ton to point to “AUTO PRESET”. Then, press the F.FWD/B button. The tuner scans and memorizes all
– CHANNEL SET UP –
ADD / DELETE CH (TV)
BAUTO PRESET
•
•
“_ _” appears at the lower left of the screen when the search has ended.
Auto Clock station- write down the number(s) that appear on the screen. These are the auto clock station(s) in your area. See item 4 below.
– AUTO CLOCK CH SEARCH –
08 10 13
_ _
the active channels in your area.
3After scanning
The tuner stops on the lowest memorized channel.
DELETING (OR ADDING)
•If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto Clock signal. Auto Clock Setting is not possible. Please use Manual Clock Setting on page 11.
Press the MENU button to exit the screen.
CHANNEL
The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)
- 12 - | EN |
