Fiber Single-mode connector types, Packaging | GarrettCom 6K16V

Magnum 6K16V Managed Fiber Switch

Installation and User Guide (06/04)

Fiber Single-mode connector types:

Fiber Port, SC-type: Fiber optic single-mode, 100BASE-FX

Fiber Port, LC-type Fiber SFF single-mode, 100BASE-FX

Fiber Port, 1000BASE-FX, GBIC modules

LEDs: Per Port (one set at the port, one set in top or front) LK: Steady ON when media link is operational ACT: ON with receiver port activity

FDX/HDX: ON = Full-Duplex Mode OFF = Half-Duplex Mode

100/10: ON = 100Mbps speed OFF = 10 Mbps

Operating Environment

Ambient Temperature:

-40° to 140° F (-40° to 60°C) for UL60950 and Component Parts rating -60° to 205° F (-50° to 95°C) for IEC 60068 Type Test short term rating

Storage Temperature: -60°to 210°F (-50°to 100°C)

Ambient Relative Humidity: 5% to 95% (non-condensing)

Altitude: -200 to 13,000 ft. (-60 to 4000m)

Conformal Coating (humidity protection) option: Request quote

Alarm Relay Contacts

One NC indicating internal power, one NC software controllable

Packaging

Enclosure: Rugged High strength sheet metal. Suitable for vertical wall or DIN-Rail mounting

Dimensions: 9.5 in. H x 8.75 in. W x 1.75 in. D 24.1 cm H x 22.2 cm W x 4.4 cm D

Cooling method: Convection, designed for vertical mounting, no fans

Weight: 4.21 lbs. (1.9 kg)

Management Console connector

DB-9 for RS-232 “ null-modem “ cable (sometimes called an X-modem cable)

Power Supply (Internal)

AC Power Connector: IEC-type, male recessed at rear of chassis,

Input Voltage: 100 to 240 VAC (auto-ranging)

Input Frequency: 47 to 63 Hz (auto-ranging) Power Consumption:

50 watts typical (for a fully loaded fiber model)

30 watts typical (for a fully-loaded copper only model)

DC Power Supply (Options)

-48VDC Power Input Voltage : -36 to -70 VDC

24VDC Power Input Voltage : 20 to 36VDC

125VDC Power Input Voltage : 115 to 150VDC

5VDC Power Input Voltage : (+) or (-) 5%

Std. Terminal Block : “ -, GND, + ”

Power Consumption: same as for AC models, see above

www . GarrettCom . com

2

Image 9

GarrettCom 6K16V manual Fiber Single-mode connector types, Operating Environment, Alarm Relay Contacts, Packaging

Contents

Managed Fiber Switch www . GarrettCom . comInstallation and User Guide Hardware Magnum 6K16V Managed Fiber Switch Hardware Installation and User GuideTrademarks Federal Communications Commission Contacting GarrettCom, IncRadio Frequency Interference Statement Reorient or relocate the receiving antenna Installation SPECIFICATIONSIntroduction OPERATION TROUBLESHOOTING 5.0 Introduction - Magnum 6K16V Managed Fiber Switch PMAPPENDIX A WARRANTY INFORMATION APPENDIX B Internal DC Power Supply Options QUAD-SERIES FIBER SWITCHES, 100 & 10MBPS, FIBER AND 6K-SERIES MANAGED FIBER SWITCHES, GIGABIT, 100 AND“OUTDOOR” ETHERNET SWITCH, FOR TEMPERATURE PERSONAL SWITCHES, 10/100MB BRIDGE PORT MODULES BPMS, 4 TYPES, FOR SEGMENT MEDIA CONVERTERS, 10MB AND 100MB SERIESTRANSCEIVERS, 10MB SERIES MINI-TRANSCEIVERS AND COAX MODELS Fiber Multi-mode connector types supported 1.0 SPECIFICATIONS 1.1 Technical SpecificationsPerformance Network Standards and Compliance, hardware Alarm Relay Contacts Fiber Single-mode connector typesManagement Console connector Power Supply Internal Agency Approvals Per-port jumpers and switchesNEBS Test Classification NEBS Compliant Email sales@GarrettCom.com for details Configuration Options Magnum Managed Fiber Switch 16 ports maxMODEL DESCRIPTION 1.2 Ordering Information fiber ports connector 2.0 Introduction 2.1 Inspecting the Package and Product 2.2 Product Description - Magnum 6K16V Managed Fiber Switch 2.2.1 Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber 100Mb, mode, and connectorFig.2.2.2 SFF Fiber Port Modules 6K8-MTRJ to the left and 6K8-MLC or -SLC below 2.2.2 Eight-Port Copper Module, 6K8-RJ45 The Magnum Combo 4@ RJ-45 + 2@ 100Mb SCsix-port modules are also available with 4@ MTRJ 100Mb mm SFF 2.2.6 Gigabit 1000Mbps port modules 2.2.4 Four-Port 10 Mb and 100Mb mm Fiber ST Modules1@ 1000Mb Fiber SC + 2@ 100Mb SC 1@ 1000Mb Fiber SC + 4@10/ 100Mb 2.2.7 Frame Buffering and Flow Control 2.2.6 Packet Prioritization, 802.1p QOS ftp//ftp.garrettcom.com 2.2.8 Managed Network Software MNS-6K for Magnum 6K16V „ Managed switching for high performance Ethernet LANs 2.3 Features and Benefits„ Switching services includes 802.1p QoS packet prioritization „ Features Fiber-Built-In 2.4 Applications Example 1 Magnum 6K16V Switch for a Industrial application Internet Fig. 2.1- The Industrial factory floor application with Magnum 6K16V SNMP Monitor 3.0 Installation 3.1 Locating Magnum 6K16V Switches3.2 Connecting Ethernet Media 3.2.2 Connecting Fiber Optic SC-type, Snap-In 3.2.1 Connecting Fiber Optic ST-type, “twist-lock”3.2.3 Connecting Single-Mode Fiber Optic IEEE Standard Media 3.2.5 Connecting Twisted Pair CAT5E or better, Unshielded or Shielded 3.3 DIN-Rail Mounting 3.2.6 Connecting Gigabit Media Using GBICs 3.3.1 Mounting Dimensions for 6K16V with metal brackets 3.4 Powering the Magnum 6K16V Managed Fiber Switch Relay Contacts 3.5 Alarm Contacts for monitoring internal power, and Software Traps 3.6.1 Preparation for Installing and Removing 6KPMs 3.6 6K16V Port Module 6KPM InstallationBe sure the power cord is unplugged and will void the warranty Step 2. Remove Chassis Cover Caution Be careful not to disturb the power supplyFigure 3.6.1a Removing the Front panel from the unit Figure 3.6.1b Magnum 6K16V, Top view without chassis cover Step 3. Remove front panel face plate retaining screws 3.6.2 Installing 6KPM Cards in the Magnum 6K16VFigure 3.6.1c Top View - 6KPM retaining screws hold Face Plate Fig 3.6.2a Granddaughter Board shown separately version for 4 copper 10/100 ports Fig. 3.6.2c Daughter Board, top view of Figure 3.6.2f Securely latching up 6KPM Cards into a Magnum 6K16V Fig. 3.6.2g Top View 6KPM Module installed inside a 6K16V 3.6.3 Removing 6KPM Cards Caution Be sure the power cord is unpluggedfirmly. Figure 3.6.3a Top View - 6 retaining s crews shown by arrows Step 3. Remove 6KPM Card DB-9 Console port connector 3.7 Connecting a Management Console Terminal to Magnum 6K16V3.7.1 RS-232 DB-9 Console Com port Serial port pin assignments Enlarged view of Magnum 6K16V Console Port area 4.0 OPERATION 4.1 Switching FunctionalityFiltering and Forwarding Address Learning Power LED, ON when external power is applied to the unit 4.3 Up-link Manual Switches set as = , for RJ-45 port onlyFull / Half duplex LED, ON when the port is running full Speed LED, ON when the speed is 100Mbps , OFF when the Auto-negotiation per-port for 802.3u-compliant switches occurs when 4.6 Power Budget Calculations for Magnum 6K16V PM’s with Fiber Media 4.5 Flow-control, IEEE 802.3x standardLXSC40 and the “Cable Loss” for 9/125 Single-mode is 0.2 dB/km LXSC70 Installation and User Guide 06/04 Magnum 6K16V Managed Fiber Switch6KP4V Km, fdx 5.0 Introduction - Magnum 6K16V Managed Fiber Switch Port Modules 5.1 Inspecting the Package and Product5.2 6KPM Module Description 5.2.1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST “twist lock” Module and configured as 10Mb ports are ST connectorsHalf-duplex by default connectors and configured module of the 6K16V Switch mode SC-type connectors. ItThe Magnum 6KP6 RJMSC is also a Combo 6 Port as 25+ Km see Power Budget, Section 5.2.5 6KP8-MTRJ, 8 @100Mb multi-mode FX , MTRJ Small-Form-factor “small-form-factor”The functionality of this 100BASE-FX multi-mode 4 port module is 6KP8-MTRJ 5.2.6 6KP8-45MT, 4@ 10/100Mbps RJ-45 and 4@100Mb multi-mode FX MTRJ connectors give an advantageMTRJ Small-Form-Factor The Magnum 6KP8-45MT 5.2.9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port connecting to a hub or another switch 5.2.11 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 6KP8VSingle-Mode Fiber port LC 5.2.12 6KM-BLNK 5.2.11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector 6.1 Before Calling for Assistance 6.0 TROUBLESHOOTING 6.3 Return Material Authorization RMA Procedure 6.2 When Calling for Assistance No Problem Found GarrettCom, Inc 213 Hammond Ave Fremont, CA Attn. Customer Service6.4 Shipping and Packaging Information B2.0 -48VDC, 24VDC and 125VDC POWER, THEORY OF OPERATION B1.0 SPECIFICATIONS FOR MAGNUM 6K16V SWITCHES, DC POWER B4.0 6K16V’S -48V, 24, 125 OR 5VDC INSTALLATION B3.0 APPLICATIONS FOR DC POWERED ETHERNET SWITCHES B7.0 TROUBLESHOOTING B4.1 UL Requirements for DC-powered unitshooked up at the last B5.0 OPERATION Power Supply Internal, 24VDC Dual-Source, model # Dual-Src-24V Power Supply Internal, 125VDC Dual-Source, model # Dual-Src-125VC3.0 DUAL-SOURCE OPTION, THEORY OF OPERATION C5.0 INSTALLATION C4.0 FEATURES AND BENEFITS OF THE DUAL-SOURCE DESIGN C6.0 ORDERING INFORMATION C5.1 UL RequirementsExample Magnum 6K16VR-48VDC C7.0 OPERATION