Telephone Jack Requirements
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a
modular jack, call your local phone company to nd out
how to get one installed.
Important Installation Information
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specically designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Temporarily disconnect any equipment connected to the phone such as
faxes, other phones, or modems.
Handset Layout
Model 29281 Slimline Memory Phone User’s GuideEquipment Approval Information
Your telephone equipment is approved for connection to the Public Switched
Telephone Network and is in compliance with parts 15 and 68, FCC Rules and
Regulations and the Technical Requirements for Telephone Terminal Equipment
published by ACTA.
1 Notication to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US number
and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this
information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number
is called. In most (but not all) areas, the sum of the RENs of all devices connected
to one line should not exceed 5. To be certain of the number of devices you may
connect to your line as determined by the REN, you should contact your local
telephone company.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
Notes
• T
his equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your
own telephone equipment if you are on a party line. Check with your local telephone
company.
• Notice must be given to the telephone company upon permanent disconnection of
your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment. If you
have questions about what will disable alarm equipment, consult your telephone
company or a qualied installer.
US Number is located on the cabinet bottom.
REN Number is located on the cabinet bottom.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone
network, the telephone company shall, where practicable, notify you that
temporary discontinuance of service may be required. Where prior notice is not
practicable and the circumstances warrant such action, the telephone company
may temporarily discontinue service immediately. In case of such temporary
discontinuance, the telephone company must: (1) promptly notify you of such
temporary discontinuance; (2) afford you the opportunity to correct the situation;
and (3) inform you of your right to bring a complaint to the Commission pursuant to
procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the
operation of its business and not inconsistent with FCC Rules and Regulations. If
these changes are expected to affect the use or performance of your telephone
equipment, the telephone company must give you adequate notice, in writing, to
allow you to maintain uninterrupted service.
Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference; and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Privacy of Communications may not be ensured when using this product.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or
television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different
from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Ofce, Washington, D.C. 20402. Please specify stock number
004-000-00345-4 when ordering copies.
Notice: The changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
3. Insert 3 AA-size alkaline batteries (not included) as shown on the diagram
inside the compartment.
4. Replace the battery compartment door.
5. Re-attach the line cord to the wall and check your memory locations. If
installation takes longer than 60 seconds, you should re-set your memory
locations.
IMPORTANT: If you’re not going to use the telephone for more
than 30 days, remove the batteries because they can leak and
damage the unit.
Setting Up the Caller ID Menu
IMPORTANT: Do not plug the telephone into the wall jack
while setting up the Caller ID menu because an incoming call
may invalidate the information not yet saved.
1. Place the handset in the cradle on the base.
2. Press the menu button. SET 5 OR 6 appears in the display.
3. Press either 5 (+) or 6 (-) button to scroll among the 7 menu screens,
which are:
• SET 5 OR 6
• Local Area Code (default - - -)
• Regional AC’s-1 (default - - - - - - - - -)
• CID LANGUAGE (default English)
• SELECT CONTRAST (default 3)
• T/P DIAL MODE (default tone)
• EXIT SETUP
NOTE: You may press dial anytime to exit the Caller ID Set Up
menu. If no buttons are pressed within 10 seconds, the phone
automatically exits the Caller ID Set Up menu and returns to
the NO CALLS summary screen.
Local Area Code
The telephone uses the programmed area code to determine the number
format to display when a valid Caller ID signal is received. It is also used for
the Dialback feature.
1. Press the menu button. SET 5 OR 6 appears in the display.
2. Press the 5 (+) button until LOCAL AREA CODE:_ _ _ appears in the
display.
3. To enter or change the area code, press the menu button. The display
shows the area code stored in memory. The left-most digit, or a minus
sign (-) ashes, indicating the unit is ready to accept the area code entry.
4. Press the 5 (+) button and select a number from 0-9 in ascending order.
Or press the 6 (-) button to select numbers from 9-0 in descending order.
5. Press the menu button to advance to the next digit.
6. After the 3rd and last digits entered, press the menu button to store the
area code and go to the next setting.
NOTE: If you make a mistake, you can simply repeat the
previous steps until your area code is set.
Regional Area Codes for 10-Digit Dialing
Like the Local Area Code, the telephone uses the programmed area codes
to determine the number format to display when a valid Caller ID signal
is received. Calls that match any of the programmed regional area codes
are displayed as 10 digits. This is helpful in areas that have multiple or
overlapping area codes and require 10-digit dialing.
1. Press the menu button. SET 5 OR 6 appears in the display.
2. Press the 5 (+) button until REGIONAL AC’S-1: _ _ _ _ _ _ _ _ _ shows in
the display.
3. To enter or change the area code, press the menu button. The display
shows the area code stored in memory. The left-most digit, or minus sign
(-), ashes, indicating the unit is ready to accept the area code entry.
4. Press the 6 (-) button, and select a number from 9-0 for the rst digit of
the area code.
5. When the desired digit is ashing, press the 5 (+) button to advance to the
next digit.
6. Press the menu button again to enter the next three-digit regional area
code and repeat steps 4 and 5 until all the REGIONAL AC’S-1 (RAC#1) and
REGIONAL AC’S-2 (RAC#1) are entered. A total of 6 sets of Regional Area
Codes may be entered.
7. Press the menu button to store the setting and return to the REGIONAL
AREA CODE display.
8. Press dial to exit.
CID Language
This setting allows you to display Caller ID display prompt messages in
English, French or Spanish.
1. Press the menu button. SET 5 OR 6 appears in the display.
2. Press the 5 (+) button until CID LANGUAGE appears in the display.
3. Press the menu button to show the current language setting. The default
is English.
4. Press the 5 (+) or 6 (-) button to change the language.
5. Press the menu button to store the language and return to the CID
LANGUAGE display.
Select Contrast
This adjustment allows you to select the contrast of the display.
1. Press the menu button until SET 5 OR 6 appears.
2. Press the 5 (+) button until SELECT CONTRAST appears in the display.
3. Press the menu button to show the current contrast setting. There are 5
levels of contrast, with the default set to 3.
4. To decrease the contrast, press 6 (-). To increase the contrast,
press 5 (+).
5. Press the menu button to store the contrast setting and return to the
SELECT CONTRAST display.
Modular
telephone
line jack
Wall plate
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
Thomson Inc.
101 West 103rd Street
Indianapolis, IN 46290-1102
© 2008 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
T/P Dial Mode
This adjustment allows you to select Tone (touch-tone) or Pulse (rotary)
dialing.
1. Press the menu button until SET 5 OR 6 appears.
2. Press the 5 (+) button until T/P DIAL MODE appears in the display.
3. Press the menu button to show the current dial mode. The default is set to
tone.
4. To change the dialing mode, press the 5 (+) or 6 (-) button. The display
will alternate between the two dialing modes.
5. Press the menu button to store the dialing mode and return to the T/P
DIAL MODE display.
Exit Setup
To immediately exit the setup mode, select the EXIT SETUP menu and press
the menu button.
REMINDER: The time and date is programmed automatically
when the rst Caller ID record is successfully received after
the unit is setup.
Telephone Basics
Connecting the Telephone Line
1. Plug the long straight line cord into a modular wall telephone jack.
2. Place the handset in the cradle.
NOTE: The unit is properly installed if you pick up the handset
and hear the dial tone. Otherwise, recheck all the installation
steps.
Wall Mount Installation
Your telephone may also be mounted on a wall plate (not included).
NOTE: To prevent the handset from falling out of the cradle
while the phone is hanging on the wall, you must reverse the
handset hook (located on the base).
store
(button) redial
(button)
ash
(button)
Introduction
Your telephone is designed to give you exibility in use and high quality
performance. To get the most from your new telephone, we suggest that you
take a few minutes right now to read through this instruction manual.
CAUTION: When using telephone equipment, there are
basic safety instructions that should always be followed.
Refer to the IMPORTANT SAFETY INSTRUCTIONS provided
with this product and save them for future reference.
Before You Begin
Parts Checklist
Make sure your package
includes the following items:
Installing the Batteries
IMPORTANT: You will have approximately 60 seconds to
replace the batteries before the memories stored in the
handset are lost. Please read the instructions before
replacing the batteries and have the batteries ready to be
inserted beforehand. As a precaution, you may want to write
down any stored information you do not want erased.
Your Caller ID phone uses 3 AA-size alkaline batteries for receiving and
storing Caller ID records and for the numbers you use for memory dialing.
1. If the telephone line cord is connected, disconnect it from the wall.
2. Open the battery compartment door with your nger or thumb.
Storing CID Records (In CID Memory)
If you are not at home or cannot answer, your telephone’s Caller ID memory
stores the data for the 50 most recent calls you received so you can see who
called while you were unavailable. When the 51st call is received, the oldest
Caller ID record (1st call) is automatically deleted.
You may review the stored information at any time. Calls received since your
last review show as NEW in the display. Calls that have not been previously
reviewed but were received from the same number more than once show as
REPT in the display.
Reviewing CID Records
As calls are received and stored, the display is updated to let you know how
many calls have been received. To scroll CID records:
1. Press either the 5 (+) or 6 (-) down button to view the newest call record.
2. Press the 6 (-) button to scroll through the call records from the most
recent to the oldest.
3. Press the 5 (+) button to scroll through the call records from the oldest to
the newest.
4. When all of the messages have been viewed, START/END appears in the
display.
Deleting CID Records
• To delete the record showing in the display, press the delete button once.
• To delete all records while reviewing, press and hold the delete button
until ERASE ALL? shows in the display, then press the delete button again
to conrm.
Dialing Back
When reviewing Caller ID records, you may dialback the phone numbers
shown on the display by pressing the dial button.
NOTE: Depending on (a) how the incoming caller’s phone
number is formatted when it is received, and (b) whether or
not you previously pre-programmed your local area code into
the set up menu, you may need to adjust the format of the
incoming caller’s stored phone number before making the
call, press the dial button to adjust the number, and try again.
If you programmed your local area code in the setup menu
1. Use the 5 (+) and 6 (-) buttons to scroll to the number you want to dial.
• If you see a number with 7 digits (i.e. 555-1234), then the call was
received from within your area code. However, this does not guarantee
the call is a local call.
• If you see a number with 11 digits (i.e. 1-234-555-1234), then the call
received was not from your area code.
2. Press the dial button and the display shows PICKUP or ADJUST. A 10
second timer also starts in the upper right side of the display, letting you
know the time remaining until the unit returns to the Summary Screen. If
you adjust the number to be dialed, the timer automatically resets itself.
3. To adjust the phone number, press the dial button. For instance, a 7-digit
local number sometimes cannot be dialed because it requires a 10-digit
or 11-digit format. Press the dial button repeatedly to scroll through the 7,
10, and 11-digit numbers.
7-digits: 7-digit telephone number (i.e. 555-5555)10-digits:
3-digit area code + 7-digit telephone number (i.e.
425-555-5555)
11-digits: long distance code 1 + 3-digit area code + 7-digit
telephone number (i.e. 1-425-555-5555)
4. To dial the displayed number, pick up the handset before the timer
reaches 0. NOW DIALING shows in the display and the number is dialed.
If you did not program your local area code in the setup menu
1. Use the 5 (+) and 6 (-) buttons to display the number you want to dial.
You will only see 10-digit numbers (i.e. 234-555-1234).
2. See steps 2 through 4 in the above section to complete the dialback
sequence.
NOTE: IF PICKUP PHONE shows on the display, no other
changes to the number can be made. The information sent
from the telephone company is known to be a valid number to
dial back (available only in limited areas). Once you pickup the
phone, the number is automatically dialed.
Memory
Before you store a telephone number in memory, make sure the dialing
mode is correctly set for the type of service you have. The default dialing
mode is tone (touch-tone), so if you have pulse (rotary) service, you must rst
change the dialing mode. See “T/P Dial Mode.”
Storing Frequently Called Numbers
1. Pick up the handset.
2. Press the store button.
3. Push the desired memory location button (0-9).
4. Press the store button.
5. Use the handset number keys to enter the telephone number (up to 16-
digits) and press the store button.
6. Hang up the handset.
NOTE: If you make a mistake, use the delete button to delete
wrong digits.
Changing a Stored Number
Repeat the storage sequence above. The new number replaces the old
number at the memory location.
Erasing a Stored Number
1. Pick up the handset.
2. Press the mem button.
3. Press the 5 (+) or 6 (-) buttons for the desired memory location to be
erased.
4. Press and hold delete for three seconds until the number in the display is
erased.
5. Hang up the handset.
NOTE: If you want to erase more than one location, use the 5
(+) or
6 (-)
arrow buttons to scroll to each memory location
you want to erase.
Dialing Frequently Called Numbers
1. Pick up the handset and press the mem button.
2. Press 0-9 for the memory location. The number dials automatically.
OR
1. Pick up the handset and press the dial button.
2. Press the 5 (+) or 6 (-) buttons for the desired memory location.
3. Press the dial button to dial the number.
OR
1. Press dial button while the handset is still in the cradle.
2. Press the 5 (+) or 6 (-) buttons for the desired memory location, lift the
handset and the number dials automatically.
Reviewing Numbers Stored in Memory
1. Press the store button.
2. Press 0-9 for the memory location. The number shows on the display.
Copy Caller ID Memory to User Memory
1. Pickup the handset.
2. Press the 5 (+) or 6 (-) buttons to display the number you want to copy.
3. Press the store button.
4. Press 0-9 for the memory location. The display ashes if the memory
location is occupied.
5. Press the store button twice to replace the new information with the
old, or press the 5 (+) or 6 (-) buttons to select an empty location. The
number is automatically stored.
6. Press the hook switch to exit.
Copy Redial Memory to User Memory
1. Pickup the handset.
2. Press store.
3. Press 0-9 for the memory location. Press the 5 (+) or 6 (-) buttons to
select a different location. The display ashes if the memory location is
occupied.
4. Press the store button again to conrm.
5. Press the redial button, and then press the store button again.
6. Press the ash button or the hook switch to exit.
Storing a Pause in Memory
The redial button has dual functionality. It becomes a pause button if the
store button is pressed rst. It is valid only when storing a number into
memory. Use the redial button to insert a pause when a delay is needed in an
automatic dialing sequence. For example, when you must dial a 9 to get an
outside line, or when you enter codes to access your long distance company.
You may need to adjust the length of the pause. It can be adjusted from 1 to
9 seconds. The default setting is 4 seconds.
1. Pickup the handset.
2. Press the store button.
3. Press the redial button.
4. Press 1-9 (1 = 1 second, 2 = 2 seconds, etc.)
5. Press store again.
6. Press the ash button or the hook switch to exit.
Chain Dialing
This process allows you to dial a succession of stored numbers from
separate memory locations. This is useful when you must dial several
sequences of numbers, such as with frequent calls via a telephone company
long distance provider.
For example Memory location
Local access number of long distance company 6
Authorization code (ID) 7
Long distance phone number 8
1. Pick up the handset.
2. Press the mem button and then press 6.
3. When you hear the access tone, press the mem button and then press 7.
4. At the next access tone, press the mem button and then 8.
TIP: Wait for the access tones before pressing the next mem
button, or your call may not go through.
Using Flash
This feature is used to activate customer calling services available through
your local phone company, such as Call Waiting. These services generally
require an extra monthly fee. If you subscribe to any of these services, please
refer to the phone company’s instructions on how to use ash.
To answer an incoming call while having a conversation:
• After you hear the Call Waiting tone, press and release the ash button.
The rst call is placed on hold while the second call can be answered.
To return to your rst call and put the second call on hold:
• Press and release ash again. The rst call can continue while the
second call is put on hold.
Using Temporary Tone Dialing
If you have pulse service, you can temporarily change from pulse to tone
service. After dialing the telephone number, press and release the *tone
button on the telephone. This allows access to phone services that require
a tone, such as banking and long-distance services. After you hang up the
handset, the telephone automatically returns to pulse service.
Caller ID Display Messages
The following special messages indicate the status of a message or the unit:
NO CALLS The caller memory is empty.
UNKNOWN CALLER The incoming call does not have Caller ID service or their service
area is not linked to yours. If UNKNOWN CALLER appears along
with a calling number, the name information for that number is
not available.
Battery power level is low. Please replace the batteries as soon
as possible in order to maintain Caller ID operation.
BLOCKED CALL The incoming caller is registered as “Private Number” and Caller
ID information is withheld.
START/END You are at the beginning or the end of the Caller ID
memory log.
CALL WAITING
If you subscribe to Call Waiting Caller ID Service, this icon
ashes when you receive a call while you are on the phone.
REPT Repeat call message. Indicates that a new call from the same
number was received more than once.
NEW Indicates call or calls have not been reviewed.
Call Waiting Caller ID
Provided you subscribe to Call Waiting Caller ID service from your phone
company; if you receive an incoming call and you are using the GE multi
handset system, a beep indicates the presence of a Call Waiting call on the
line. The Call Waiting Caller ID information will be displayed and stored in the
history of all handsets in the system.
•
When you hear the call waiting beep in the handset receiver, press the ash
button to put the current call on hold and answer the incoming call. Press
ash again to return to the original call.
Receiving CID Records
When you receive a call, the Caller ID information is transmitted between the
rst and second ring. The Caller ID information appears on the display while
the phone rings, giving you a chance to monitor the information and decide
whether or not to answer the call.
Model 29281
00021389 (Rev. 1 Dom E/S)
08-05
Printed in China
*tone
(button)
Ringer
Volume
mem
(memory
button)
Visit our website at: www.GE.com/phones
Current time Current date
Caller ID
name
Caller ID
number
New calls
menu
(button)
delete
(button)
display
dial
(button)
volume
switch
5(
+) /
6(
-)
(buttons)
Battery compartment
Handset Back
Troubleshooting Tips
No dial tone.
• Check all cabling to make sure that all connections are secure and not damaged.
• Check the hook switch: Does it fully extend when handset is lifted from cradle?
No display
• Replace batteries.
• Make sure the batteries are properly installed.
No information is shown after the phone rings
• In order to receive Caller ID records, you must subscribe to the standard name and
number Caller ID service available through your local telephone company.
• Be sure to wait until the second ring before answering.
Phone does not ring
• Make sure ringer switch is set to HI.
• You may have too many extension phones on your line. Unplug some extension
phones.
• Check for a dial tone. If there is no dial tone see solutions for “No dial tone.”
Other party cannot hear you
• Make sure phone cord is securely plugged in.
• Make sure extension phones are on the hook at the same time you’re using the
phone. It is normal for the volume to drop when additional extension phones are
used at the same time.
Cannot dial out
• Make sure the T/P dialing mode is set to the type of phone service you are
subscribed to.
Service
If trouble is experienced with this equipment, for repair or warranty information, please
contact customer service at 1-800-448-0329. If the equipment is causing harm to the
telephone network, the telephone company may request that you disconnect the equipment
until the problem is resolved.
This product may be serviced only by the manufacturer or its authorized service agents.
Changes or modications not expressly approved by Thomson Inc. could void the user’s
authority to operate this product. For instructions on how to obtain service, refer to the
warranty included in this guide or call customer service at 1-800-448-0329.
Or refer inquiries to:
Thomson Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or jot down the date this
product was purchased or received as a gift. This information will be valuable if service
should be required during the warranty period.
Purchase Date
Name of Store
Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year, from date of purchase.
(The warranty period for rental units begins with the rst rental or 45 days from date of
shipment to the rental rm, whichever comes rst.)
What we will do:
• Provide you with a new. The exchange unit is under warranty for the remainder of the
original product’s warranty period.
How you get service:
• Properly pack your unit. Include any cables, etc., which were originally provided with the
product. We recommend using the original carton and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that
the product is within the warranty period, must be presented to obtain warranty service.”
For rental rms, proof of rst rental is also required. Also print your name and address
and a description of the defect. Send via standard UPS or its equivalent to:
Thomson Inc.
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service not covered by the
warranty.
• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in case of
damage or loss.
• A new unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding operating
instructions and user controls. Any additional information, should be obtained from your
dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modied or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please visit www.ge.com/phones to register your unit. It will make it easier to contact
you, should it ever be necessary. Registration is not required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS
PRODUCT. ALL OTHER WARRANTIES, ExPRESS OR IMPLIED (INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE
HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON
INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE ExCLUSIVE
REMEDY OF THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEqUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT
OR ARISING OUT OF ANY BREACH OF ANY ExPRESS OR IMPLIED WARRANTY ON
THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE
GOVERNED BY THE LAWS OF THE STATE OF INDIANA. ExCEPT TO THE ExTENT
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above limitations or
exclusions may not apply to you.
• This warranty gives you specic legal rights, and you also may have other rights that vary
from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.
1. Push the handset hook up and out of the slot on the base with your thumb,
rotate the hook 180°, and replace it back in the slot.
2. Feed the line cord through the groove and wrap the cord around the track
on the bottom of the base.
3. Feed the line cord through the groove on the opposite side of the track,
and plug the end into the modular telephone jack.
4. Slip the mounting holes (on the bottom of the base) over the wall plate
posts and rmly slide the unit down into place.
Adjusting the Ringer Volume
You may control the ringer volume level with the switch located on the side
of the base.
= ringer tone will be loud
= ringer tone will be low
= telephone will not ring
Adjusting the Volume
You may control the listening level with the VOLUME switch, which has three
levels. It remains at the last level set until you change it.
Redialing a Number
If you want to call the last number you dialed again (up to 32 digits), use the
redial feature.
1. Pick up the handset.
2. Press the redial button.
3. The last number called is automatically redialed.
Using One Touch Redial
If the last call you dialed was busy, you can redial it immediately by just
pressing the redial button and without hanging up the handset.
Caller ID (CID)
IMPORTANT: In order to use this unit’s Caller ID features, you
must subscribe to either the standard Name/Number Caller
ID Service or Call Waiting Caller ID Service. To know who is
calling while you are on the phone, you must subscribe to Call
Waiting Caller ID Service.
This unit receives and displays information transmitted by your local phone
company. This information can include the phone number, date, and time; or
the name, phone number, date, and time.