Installation Instructions

1

INSTALLING THE WATER LINE (ON SOME MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of tubing you need. Approved plastic water supply lines are GE SmartConnectRefrigerator Tubing (WX08X10002, WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow the manufacturer’s recommendations.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position (on power switch models) or the feeler arm is in the STOP (up) position (on feeler arm models).

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with local plumbing code requirements.

WHAT YOU WILL NEED

Copper or GE SmartConnectRefrigerator Tubing kit, 1/4″ outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then add 8′ (2.4 m). Be sure there is sufficient extra tubing (about 8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.

GE SmartConnectRefrigerator Tubing Kits are available in the following lengths:

2′

(0.6 m)

– WX08X10002

6′

(1.8 m)

– WX08X10006

15′ (4.6 m)

– WX08X10015

25′ (7.6 m)

– WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m) as described above.

NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnectRefrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.

13

Page 13
Image 13
GE 17 operating instructions Installing the Water Line on Some Models, Before YOU Begin, What YOU will Need

17 specifications

General Electric (GE) is known for its longstanding tradition of innovation and engineering excellence, encompassing a wide array of products across various industries. Among its notable offerings are its GE 18, 17, and 16 series of gas turbines, designed for power generation. These turbines exemplify technological advancement, efficiency, and reliability in modern energy production.

The GE 18 series, often referred to as the 7HA.02, is a high-efficiency gas turbine that achieves a thermal efficiency of over 64%. This series utilizes advanced materials and manufacturing processes, enabling it to withstand higher temperatures and pressures, thereby maximizing performance. With its ability to operate on a varied mix of fuels, including natural gas and low heating value gases, the GE 18 series stands out for its versatility. Its modular design simplifies maintenance, allowing for shorter downtimes and enhanced operational availability.

The GE 17 series, known as the 7F.05, offers a robust solution for mid-range power generation. With an efficiency rating around 58%, the 17 series is designed for both simple cycle and combined cycle applications. One of its key features is the incorporation of advanced aerodynamics in its turbine blades, which contributes to lower emissions and higher output. Additionally, the GE 17 series comes equipped with digital technologies, such as GE’s Digital Wind Farm and asset performance management tools, allowing operators to monitor and optimize performance in real time.

The GE 16 series, also called the 9FB, is known for its flexibility and high reliability in power generation. It boasts an efficiency rate of approximately 60% when operated in combined cycle mode. The 16 series is designed for easy integration into existing facilities, making it an ideal choice for upgrades and expansions. Its advanced combustion technology minimizes nitrogen oxide emissions, complying with stringent environmental regulations. Furthermore, the GE 16 series employs advanced sensors and control systems that enhance operational efficiency and safety, ensuring it remains a competitive option in the market.

In summary, GE's 18, 17, and 16 series gas turbines represent the forefront of power generation technology, offering unmatched efficiency, flexibility, and environmental performance. Each series is engineered with unique features to cater to different operational needs, ensuring that GE continues to play a pivotal role in the energy landscape. With ongoing innovations and a commitment to sustainability, GE remains a leader in the gas turbine market.