Installation Instructions

INSTALLING THE ANTI-TIP FLOOR BRACKET (on 21 ft. models)

WARNING

Under certain circumstances, this refrigerator can tip forward.

Injury to persons can result.

Install Anti-Tip Bracket packed with this refrigerator.

1MEASURE CABINET OPENING AVAILABLE VS. REFRIGERATOR WIDTH

Measure width of cabinet opening where refrigerator will be placed, W.

Be sure to account for any countertop overhang, baseboard thickness and any clearance desired. Width, W, should not be less than 36 inches. The refrigerator will be placed approximately in the middle of this opening.

2LOCATING THE ANTI-TIP FLOOR BRACKET

APlace the anti-tip floor bracket locator template (included inside the anti-tip kit) onto the floor up against the rear wall, within W, and in line with the desired location of the RH side of the refrigerator (see Figure 1).

Figure 1 – Installation Overview

Floor – Concrete

2 Wall Holes

 

 

 

(2 Holes)

 

Floor Bracket

Floor – Wood

 

to Install

(2 Holes)

 

RH Holes

 

71⁄4″

 

 

 

Rear RH Corner

Base

 

of Cabinet Wall

Bracket

 

 

on the

RH Side of

Locator Template

Refrigerator

Refrigerator

Sheet

BPlace the anti-tip floor bracket onto the locator template with its RH floor holes lined up with the floor holes indicated on the template sheet, approximately 71⁄4″ from the edge of the sheet or the RH side of the refrigerator.

Rear Wall

W

REFRIGERATOR

Baseboard

Thickness

or Countertop Overhang (Whichever

Is Greater) Plus Any Desired Clearance

RH Side

C Hold down in position and use the anti-tip floor

bracket as a template for marking the holes

based upon your configuration and type of

construction as shown in Step 3. Mark the hole

locations with a pencil, nail or awl.

NOTE:

• It is REQUIRED to use at least 2 screws to

mount the floor bracket (one on each side of

the anti-tip floor bracket). Both must be into

either the wall or the floor. Figure 2 indicates

Front

all the acceptable mounting configurations

for screws. Identify the screw holes on the

anti-tip floor bracket for your configuration.

18

Page 17 Page 19
Page 18
Image 18
GE 200D9366P019 installation instructions Measure Cabinet Opening Available VS. Refrigerator Width
Page 17 Page 19

200D9366P019 specifications

The GE 200D9366P019 is a sophisticated component primarily recognized for its use in industrial applications, particularly in automation and control systems. This product, developed by General Electric, showcases remarkable features that integrate advanced technology for enhanced performance and reliability.

One of the main features of the GE 200D9366P019 is its robust design, engineered to withstand harsh industrial environments. This durability ensures that the component remains operational even under extreme conditions such as temperature fluctuations, vibration, and dust. This inherent toughness is vital in maintaining system integrity, reducing downtime, and lowering maintenance costs.

The GE 200D9366P019 incorporates cutting-edge technologies that facilitate seamless integration into various systems. The component is designed with compatibility in mind, allowing it to work harmoniously with other GE products and third-party systems. This interoperability is a significant advantage for users looking to expand or upgrade their existing setups.

Another key characteristic of the GE 200D9366P019 is its high level of precision and accuracy. The component is engineered to deliver consistent performance, which is essential in applications requiring exact measurements and control. This precision contributes to superior process management and enhances the overall efficiency of the systems it is integrated into.

The GE 200D9366P019 also features advanced communication capabilities. With support for various communication protocols, this component facilitates real-time data exchange between devices, allowing for improved monitoring and control. This connectivity is crucial in today’s smart manufacturing environments, where integrated systems play a critical role in optimizing workflows and reducing operational costs.

In addition to its technical features, the GE 200D9366P019 is backed by the extensive support and resources offered by General Electric. Users benefit from comprehensive documentation, troubleshooting guides, and customer service, ensuring they can maximize the potential of their investment.

Overall, the GE 200D9366P019 stands out as a reliable and versatile component in the realm of industrial automation. Its robust design, advanced technologies, and precise capabilities make it an ideal choice for businesses seeking to enhance their operational efficiency and maintain high standards of quality.
Top Page Image Contents