Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.

Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.

 

Standard Depth

Counter Depth

 

Models

Models

Sides

1/8(3 mm)

1/8(3 mm)

Top

1(25 mm)

1(25 mm)

Back

1(25 mm)

1/2(13 mm)

REMOVE TOP CAP (on some models)

IMPORTANT NOTE: This refrigerator is 34-1/2deep.

Doors and passageways leading to the installation location must be at least 36wide in order to leave the doors and handles attached to the refrigerator while transporting it into the installation location. If passageways are less than 36, the refrigerator doors and handles can easily be scratched and damaged. The top cap and doors can be removed to allow the refrigerator to be safely moved indoors. Start with Step A.

If it is not necessary to remove doors, skip Step A. Leave tape and all packaging on doors until the refrigerator is in the final location.

SKID REMOVAL: Tilt refrigerator to each side to remove skid.

NOTE: Use a padded hand truck to move this refrigerator. Place the refrigerator on the hand truck with a side against the truck. We strongly recommend that TWO PEOPLE move and complete this installation.

ALocate and remove the two Phillips head screws on the top of the refrigerator. Remove the two screws on each side at the rear of the top cap.

Lift off and remove top cap.

BRemove the fresh-food door. Refer to Steps 1 through 3 of “Reversing the Door Swing” section.

CRemove the bottom freezer drawer. Refer to “Removing Freezer Drawer” section.

DMove refrigerator to the installation location.

REMOVE TOP CAP (cont.) (on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

ECarefully lower the door onto the center hinge. Reinstall top hinge. NOTE: Ensure the door is properly aligned to the case top to avoid readjustment of the door during top cap reinstallation.

FPlace cap over the top of the refrigerator. Reinstall the original screws in the top and back of the cap.

GReinstall the bottom freezer drawer. Refer to “Replacing the Freezer Drawer” section.

A

Top Hinge B

1CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker operation. If there is not a cold water supply, you will need to provide one. See Installing the Water Line section.

NOTES:

Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

If your refrigerator does not have a water filter, we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnectRefrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.

20

Page 20
Image 20
GE 200D9366P019 Installing the Refrigerator, Refrigerator Location, Clearances, Remove TOP CAP cont. on some models

200D9366P019 specifications

The GE 200D9366P019 is a sophisticated component primarily recognized for its use in industrial applications, particularly in automation and control systems. This product, developed by General Electric, showcases remarkable features that integrate advanced technology for enhanced performance and reliability.

One of the main features of the GE 200D9366P019 is its robust design, engineered to withstand harsh industrial environments. This durability ensures that the component remains operational even under extreme conditions such as temperature fluctuations, vibration, and dust. This inherent toughness is vital in maintaining system integrity, reducing downtime, and lowering maintenance costs.

The GE 200D9366P019 incorporates cutting-edge technologies that facilitate seamless integration into various systems. The component is designed with compatibility in mind, allowing it to work harmoniously with other GE products and third-party systems. This interoperability is a significant advantage for users looking to expand or upgrade their existing setups.

Another key characteristic of the GE 200D9366P019 is its high level of precision and accuracy. The component is engineered to deliver consistent performance, which is essential in applications requiring exact measurements and control. This precision contributes to superior process management and enhances the overall efficiency of the systems it is integrated into.

The GE 200D9366P019 also features advanced communication capabilities. With support for various communication protocols, this component facilitates real-time data exchange between devices, allowing for improved monitoring and control. This connectivity is crucial in today’s smart manufacturing environments, where integrated systems play a critical role in optimizing workflows and reducing operational costs.

In addition to its technical features, the GE 200D9366P019 is backed by the extensive support and resources offered by General Electric. Users benefit from comprehensive documentation, troubleshooting guides, and customer service, ensuring they can maximize the potential of their investment.

Overall, the GE 200D9366P019 stands out as a reliable and versatile component in the realm of industrial automation. Its robust design, advanced technologies, and precise capabilities make it an ideal choice for businesses seeking to enhance their operational efficiency and maintain high standards of quality.