Through-the-Wall Installation Instructions—Optional

The case may be installed through-the-wall in both existing and new construction.

Read completely, then follow step-by-step.

NOTE: Obtain all materials locally for mounting the air conditioner through- the-wall.

1

D

IMPORTANT (cont.)

Secure with 14 wood screws anchored at least an inch into the wall support structure.

NOTE: Drill pilot holes, if necessary, for proper installation. If the frame is oversized, use shims to prevent case distortion.

1IMPORTANT

Through-the-wall installation is not appropriate if any of the side or top louvers in the case will be obstructed by the wall.

All side and top louvers in the case must project on the outdoor side of the wall.

The room side of the case must project into the room far enough to maximize the balance of the unit.

The case must be installed level from side- to-side and with a slight tilt from front to rear. Use a level; no more than a 1/2 bubble will be the correct case slant to the outside.

Lintel angle is required to support bricks or blocks above opening.

Flashing is required and should extend the length of the opening to ensure no inside cavity leakage occurs.

ARemove the air conditioner from the case. For specific instruction, refer to the Window Installation Instructions.

BMake certain that a wall receptacle is available close to the hole location or make arrangements to install a receptacle.

CPlace the case in the wall opening and place wood support strips between the case bottom and the flashing on both sides of the bottom rail. They should be the same height as the bottom rail and the same length as the wall opening.

2FINISH THE WALL OPENING

ACaulk all four sides on the outdoor side of the case to prevent moisture from getting through to the interior wall. Use of flashing (drip rail) will further prevent water from dripping inside the wall and down the outside of the building.

 

Plaster line

Lintel angle

 

Caulking

Trim molding

 

(if desired)

OUTSIDE

INSIDE

 

Air louvers

 

(top and

Bottom rail

sides must

 

project on the

 

outdoor side

 

of the wall)

 

Wood filler and caulking (above and below the flashing)

Case Bottom

Flashingbottom rail (Drip rail)

Flashing

(Drip rail)

Wood support strips

BPlace the air conditioner into the case.

For specific instruction, refer to the Window Installation Instructions.

15

Page 15
Image 15
GE ASM14*, ASM24*, ASQ18 Through-the-Wall Installation Instructions-Optional, Finish the Wall Opening

ASQ18, ASM24*, ASM14* specifications

GE ASM14*, ASQ18, ASM24* are part of General Electric's advanced suite of air compressor technologies designed for energy efficiency and reliability. These models cater to various industrial applications that require compressed air solutions, offering distinct features that enhance operational performance.

The ASM14* model is engineered with advanced airend technology, which ensures increased efficiency and reduced power consumption. This results in lower operational costs while providing consistent airflow. It employs a robust design that minimizes maintenance needs, making it a preferred choice for industries looking for reliable performance without frequent downtime.

ASQ18 offers high adaptability to different environmental conditions. This model features integrated variable speed drive (VSD) technology, which adjusts the compressor output based on the actual air demand. This not only optimizes energy consumption but also reduces wear and tear, extending the lifecycle of the unit. ASQ18 is perfect for facilities that experience fluctuating air requirements and emphasizes sustainability through reduced energy usage.

Similarly, the ASM24* model brings impressive capabilities to the table, particularly in terms of airflow and pressure characteristics. Its compact design allows easy integration into existing setups, and it boasts a low noise level, making it suitable for various applications where noise reduction is critical. This model incorporates easy-to-access components that simplify maintenance, ensuring operational continuity.

All three models utilize advanced monitoring technologies, providing real-time data on performance and operational health. This enables users to make informed decisions regarding maintenance schedules, ultimately enhancing productivity. Additionally, GE’s commitment to incorporating smart technologies ensures compatibility with predictive maintenance systems, allowing for proactive issue resolution.

In summary, the GE ASM14*, ASQ18, and ASM24* compressors stand out for their commitment to efficiency, sustainability, and reliability. With their advanced engineering, they cater to diverse industrial needs while helping businesses minimize operational costs and enhance productivity. Choosing these models means capitalizing on GE's legacy of quality and innovation in the compressed air sector.