Dishwasher Installation
10

STEP 16: POSITION DISHWASHER, SECURE

TO COUNTERTOP OR CABINET

In this step you will need the 2 Phillips special head screws
from the screws set aside in Step 1.
The dishwasher must be secured to the countertop or the
cabinet sides. When the underside of the countertop is wood,
use Method 1. Use Method 2 when the underside of the
countertop is made of a material, such as granite, that will not
accept wood screws.
IMPORTANT – Prevent door panel and control
panel damage. Dishwasher must be positioned so the front
panel and control panel do not contact the adjacent cabinets
or countertop. Mounting screws must be driven straight and
flush. Protruding screw heads could scratch the door panel or
control panel and interfere with door operation.
Method 1
Secure dishwasher to underside of wood countertop.
• Recheck alignment of the dishwasher in the cabinet. Refer to
Steps 14 and 15. Door panel and/or control panel must not
hit cabinets or countertop.
• Fasten the dishwasher to the underside of the countertop
ZLWKWKH3KLOOLSVVSHFLDOKHDGVFUHZV5HIHUWR¿JXUH
0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW
panel damage.
Method 2
Secure dishwasher to cabinet sides.
• Recheck alignment of the dishwasher in the cabinet. Refer
to Steps 14 and 15. Door panel and/or control panel must
not hit cabinets or countertop. Remove plug buttons. Do not
discard.
• Remove plug buttons. Do not discard.
• Fasten the dishwasher to the adjacent cabinets with the
2 Phillips special head screws provided. Refer to Figure X.
0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW
panel damage.
• Install plug buttons to the side of the tub in the holes
provided.
Figure X

Solid Surface Countertop

Side Brackets
Plug buttons
Screws Screws

STEP 17: CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.
If using a flexible braided hose connection:
• Attach nut to 90° elbow using an adjustable wrench.
If using a copper tubing connection:
• Slide compression nut, then ferrule over end of water line.
• Insert water line into 90° elbow.
• Slide ferrule against elbow and secure with compression nut.
IMPORTANT – Check to be sure that door spring
DQGRUGRRUVSULQJFDEOHGRQRWUXERUFRQWDFWWKH¿OOKRVHRU
water supply line.
Test by opening and
closing the door.
Reroute the water
supply lines if a
rubbing noise or
interference
occurs.

STEP 18: CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8" through 1"
diameter inlet ports on the air gap, waste tee or disposer.
• Determine size of inlet port.
• Cut drain hose connector on the marked line, if required,
WR¿WWKHLQOHWSRUW
• If a longer drain hose is required and you did not purchase
drain hose GPF12 or WD24X10065, add up to 66" length for a
total of 144" (12 feet) to the factory-installed hose. Use 5/8" or
7/8" inside diameter hose and a coupler to connect
the 2 hose ends.
Secure the
connection
with hose
clamps.
Figure Z
Figure AA
NOTE: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 15 FEET
FOR PROPER DRAIN OPERATION.
7^bT2[P\_
2^d_[Ta 7^bT2[P\_
Cutting Line
1" 5/8"
IMPORTANT: Do not cut corrugated
portion of hose
Figure Y
Compression
Nut
Hot Water
Supply Line
90° Elbow
Ferrule
Bottom Left Side
Brackets Wood Countertop