GEH-5304A

Mounting may be either horizontal or vertical for these bearing life determinations, as long as no axial load (i.e., suspended load) other than the weight of the armature is present if vertical.

5.Special Load Considerations

Where the load is overhung beyond the motor shaft extension or greater bearing life is desired, the application should be referred to GE Industrial Systems.

6.Pinion Drives

While Kinamatic® motors are not designed for overhung pinion drives, they may be successfully ap- plied under suitable conditions. In addition to a radial load, some gears produce thrust load on the bearing. Complete details of the proposed gearing should be referred to GE Industrial Systems in all cases.

7.Thrust Loads

Due to the mounting position or type of drive arrangement, a thrust load may be applied to the motor shaft. The Kinamatic® motor is designed to permit a limited amount of thrust load. This permissible load will vary by mounting position and direction of the load due to the weight of the armature. The permissible load in Table 2 is tabulated by frame diameter and mounting position. These apply to ball bearings only.

For applications combining thrust and radial loads or where thrust loads exceed the values shown in Table 2, refer all details to GE Industrial Systems.

Table 2

Maximum Continuous Thrust Capacity, Lbs.*

 

 

 

Vertical Mounting

 

Bearing

Horizontal

Thrust Load

Thrust Load

Frame

Size

Mounting

Up

Down

2512

Std-309

350

465

235

2512

O/S-310

400

515

285

2513

Std-309

350

485

215

2513

O/S-310

400

585

265

2812

Std-310

400

550

250

2812

O/S-311

500

650

350

2813

Std-310

400

585

215

2813

O/S-311

500

685

315

*Based on L10 life of 20,000 hours and an average speed not exceeding 2500 RPM.

IV. OPERATION

Disconnect power before touching any internal part. High voltage may be pres- ent even when the machine is not rotating. If used with a rectified power sup- ply, disconnect all AC line connections to power supply. With other power supplies, disconnect all DC line and field connections. Also disconnect power from auxiliary devices.

Ground the machine properly to avoid serious injury to personnel. Grounding must be in accordance with the National Electrical Code and consistent with sound local practices. One of the bolts holding the conduit box to the unit, ac- cessible from inside the conduit box, is identified and may be used for attach- ing a grounding cable.

11

Page 10 Page 12
Page 11
Image 11
GE GEH-5304A manual Special Load Considerations, Pinion Drives, Thrust Loads, Maximum Continuous Thrust Capacity, Lbs
Page 10 Page 12

GEH-5304A specifications

The GE GEH-5304A is a sophisticated electronic device that has garnered attention for its applications in various industrial sectors. This cutting-edge equipment is primarily used for monitoring and controlling processes through advanced technology integration, making it a valuable asset for businesses looking to enhance operational efficiency.

One of the standout features of the GE GEH-5304A is its robust data acquisition system. This system effectively collects, processes, and analyzes data from multiple sensors and instruments, enabling real-time monitoring of critical parameters. With its high sampling rate and accuracy, the GEH-5304A ensures that users can make informed decisions based on reliable data, thus minimizing risks and enhancing productivity.

The GEH-5304A integrates seamlessly with various communication protocols, including Ethernet, RS-232, and RS-485. This versatility allows it to connect effortlessly to existing infrastructure and facilitates data sharing across different platforms. This interoperability is essential in modern industrial environments, where different systems must communicate for optimal performance.

Another key characteristic of the GEH-5304A is its user-friendly interface. The device features an intuitive display that provides clear visualizations of data trends, alarms, and system statuses. This ease of use empowers operators to quickly identify issues and make necessary adjustments, thereby reducing downtime and improving overall operational reliability.

In terms of advanced technology, the GEH-5304A boasts built-in diagnostics and predictive maintenance capabilities. These features enable it to identify potential problems before they escalate into failures, allowing for proactive maintenance and minimizing costly unscheduled outages. Moreover, the device's ability to log historical data plays a crucial role in trend analysis and long-term planning.

Durability is another hallmark of the GE GEH-5304A. Designed to withstand harsh industrial conditions, it demonstrates resilience against temperature fluctuations, vibration, and dust. This robustness enhances its longevity and reduces the frequency of replacements and repairs.

In summary, the GE GEH-5304A stands out in the market due to its advanced data acquisition capabilities, compatibility with multiple communication protocols, user-friendly interface, predictive maintenance functionalities, and rugged design. These features make it an essential tool for industries seeking to optimize performance, enhance monitoring, and ensure process reliability. With the ongoing evolution of technology, devices like the GEH-5304A are pivotal in driving operational success across various sectors.
Top Page Image Contents