Safety Instructions

Operating Instructions

Troubleshooting Tips

Consumer Support

About the dishwasher control panel. (For models with sensor: EDW6000 Series,

GHDA600 Series, GLD6000 Series)

You can locate your model number on the tub wall just inside the door. Throughout this manual, features and appearance may vary from your model.

 

1

 

 

3

5

4

2

Control Settings

1Status Indicator Lights

The Status display tells you what’s happening while the dishwasher is in operation and may flash, indicating a malfunction (see page 8). The lights will come ON indicating the sequence of operation the dishwasher is in.

SENSING

Displayed while the sensor is measuring the amount of soil and temperature of water.

(on some models)

The dishwasher will adjust the selected cycle to achieve optimal performance.

 

 

WASHING Displayed during prewash and main wash periods. (on some models)

RINSING Displayed during rinse periods. (on some models)

DRYING Displayed during HEATED DRY. (on some models)

SANITIZED Displayed when cycle has met sanitization conditions. Light remains ON until door is opened.

CLEAN Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean until the door is relatched or until another cycle is selected.

2Time Remaining Display (on some models)

During operation, the display shows the minutes remaining until the cycle is complete. The display may adjust the remaining time while the sensing light is on. The time displayed at the start of each cycle may change from the factory setting as the unit customizes itself to home use. During a delay start, the display will show hours of time remaining until the cycle starts.

3

Cycles

 

The light above the selected pad will be ON to indicate which cycle has been selected.

 

This dishwasher is equipped with a dirt and temperature sensor. Cycle length and time will vary depending on the soil level and temperature.

ANTI-BACTERIA

Heavy 8.5 gal., 84 min.

or SANI WASH

Medium 7.3 gal., 78 min.

 

Light 6.1 gal., 75 min.

This cycle raises the water temperature in the final rinse to sanitize your dishware. The cycle length will vary depending on the temperature of your inlet water.

NOTE: The Anti-Bacteria cycle is monitored for sanitization requirements. If the cycle is interrupted during or after the main wash portion or if the incoming water temperature is so low that adequate water heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the sanitized light will not illuminate at the end of the cycle.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

POTS

Heavy 10.9 gal., 102 min.

& PANS

Medium 8.5 gal., 78 min.

 

Light 7.3 gal., 73 min.

This cycle is meant for heavily soiled dishes or cookware with dried-on or baked-on soils.

Everyday dishes are safe to be used in this cycle.

 

NORMAL WASH Heavy 8.5 gal., 65 min.

 

Medium 7.3 gal., 60 min.

4

Light 4.9 gal., 49 min.

 

This cycle is for medium/heavily soiled dishes and glassware.

Page 3 Page 5
Page 4
Image 4
GE GLDL500 owner manual Safety Instructions, Troubleshooting Tips Consumer Support, Status Indicator Lights, Cycles
Page 3 Page 5

GLDL500 specifications

The GE GLDL500 is an innovative and advanced gas turbine engine designed for various applications, including power generation and industrial processes. Known for its efficiency, reliability, and advanced technology, the GLDL500 is a prime example of General Electric's commitment to producing cutting-edge energy solutions.

One of the main features of the GE GLDL500 is its high efficiency. The engine is designed to operate at an impressive thermal efficiency, allowing for lower fuel consumption and reduced emissions. This efficiency not only contributes to cost savings but also supports environmental sustainability efforts by minimizing the carbon footprint of operations.

The GLDL500 incorporates advanced materials and manufacturing techniques that enhance its performance and durability. It utilizes heat-resistant superalloys in its turbine section, which allow the engine to withstand the extreme temperatures and stresses experienced during operation. This not only prolongs the lifespan of the turbine but also improves the overall reliability of the system.

Another key characteristic of the GE GLDL500 is its modular design. This design enables easy maintenance and upgrades, making it a flexible choice for operators looking to adapt to changing energy demands or to incorporate new technologies. The modularity also simplifies logistics and reduces downtime, leading to increased operational efficiency.

The GLDL500 features advanced digital controls and monitoring systems. These systems provide real-time data on engine performance, allowing operators to make informed decisions and optimize the turbine's operation. The incorporation of digital technologies fosters predictive maintenance, helping to identify potential issues before they become significant problems.

In terms of environmental performance, the GE GLDL500 is compliant with stringent emission regulations. The engine is engineered to minimize NOx and CO2 emissions, ensuring that it meets or exceeds industry standards. This focus on clean energy solutions aligns with global efforts to transition towards more sustainable energy sources.

Overall, the GE GLDL500 stands out as a powerful, efficient, and environmentally friendly gas turbine engine. Its combination of advanced features, innovative technologies, and robust characteristics makes it an ideal choice for a variety of applications in the modern energy landscape, demonstrating GE's leadership in the gas turbine market. Operators investing in the GLDL500 can expect enhanced performance, reduced operational costs, and a commitment to sustainability.
Top Page Image Contents