About the water softener system.

Breaking a Salt Bridge

Sometimes, a hard crust or salt bridge forms in the salt storage area. It is usually caused by high humidity or the wrong kind of salt. When the salt bridges, an empty space forms between the water and salt. Then salt will not dissolve in the water to make brine.

If the brine tank is full of salt, it is hard to tell if you have a salt bridge. Salt is loose on top, but the bridge is under it. The following is the best way to check for a salt bridge.

Salt should be loose all the way to the bottom of the tank. Take a broom handle or like tool, and carefully push it down into the salt, working it up and down. If the tool strikes

a hard object (be sure it’s not the bottom or sides of the tank), it’s most likely a salt bridge. Carefully break the bridge with the tool.

Do not pound on the walls of the tank.

If the wrong kind of salt made the bridge, take it out. Then fill the tank with nugget or pellet salt only. In humid areas, it is best to fill with less salt, more often to prevent a salt bridge from forming.

Push tool into salt bridge to break

1–2

Pencil mark

 

Salt

Broom

Salt

handle

 

bridge

 

Water level

Cleaning the Nozzle and Venturi Assembly

A clean nozzle and venturi is needed for the water softening system to work properly. This small unit makes the suction to move brine from the salt storage area to the resin tank during recharge. If it becomes plugged with sand, dirt, etc., the water softening system will not work and you will get hard water.

To get to the nozzle and venturi, remove the water softening system top cover. Be sure the water softening system is in service cycle (no water pressure at nozzle and venturi). Then, while holding the nozzle and venturi housing with one hand, remove the cap. Lift out the screen support and screen, then the nozzle and venturi. Wash and rinse the parts in warm water until clean. If needed, use a small brush to remove iron or dirt. Also check and clean the gasket.

NOTE: Some models have a small flow plug located in the nozzle and venturi, and/or a small cone shaped screen in the housing. Be sure to check and clean these parts,

if your model is so equipped.

Carefully replace all parts in the correct order. Lightly lubricate the o-ring seal with clean silicone grease or petroleum jelly and place in position. Install and tighten the cap, by hand only.

Do not overtighten the cap.

12

Cap

O-ring seal

Screen support

Screen

*Flow plug

Nozzle & Venturi

 

Screen

 

Gasket

*Flow plug

Nozzle & Venturi housing

IMPORTANT: Be sure small holes in the gasket are centered directly over the small holes in the nozzle and venturi housing.

*Install with numbered side up, concave side down.

Page 12
Image 12
GE GXSF31E Breaking a Salt Bridge, Cleaning the Nozzle and Venturi Assembly, Do not overtighten the cap

GXSF31E specifications

The GE GXSF31E is a state-of-the-art water filtration system that effectively addresses the need for clean and great-tasting water in residential applications. This model focuses on efficiency, reliability, and advanced filtration technologies that enhance water quality for everyday use.

One of the main features of the GE GXSF31E is its robust filtration capabilities. It utilizes a dual-stage filtration process that combines sediment filtration with activated carbon block technology. This dual approach not only removes common contaminants such as chlorine, sediment, and rust but also significantly improves the taste and odor of your water. As a result, users enjoy water that is not only safe but also refreshing and pleasant to drink.

In terms of capacity, the GE GXSF31E is designed to meet the needs of medium to large households. With a production capacity of up to 31,000 grains, it is capable of efficiently handling the water demands of families with multiple members. The system features a digital control panel that allows users to monitor and manage the filtration process effectively, providing alerts for filter replacements and ensuring optimal performance at all times.

The GE GXSF31E also incorporates advanced technologies for ease of maintenance. The unit is equipped with a self-cleaning mechanism that helps reduce the need for manual cleaning, thereby extending the lifespan of the filters and the system as a whole. This feature significantly enhances convenience, as homeowners can rely on the unit to maintain its efficiency without constant intervention.

Energy efficiency is another critical characteristic of the GE GXSF31E. The system is designed to operate with minimal energy consumption, making it an environmentally friendly choice for responsible consumers. Additionally, its compact design allows for easier installation and integration into limited spaces, which is particularly advantageous for urban settings.

The GE GXSF31E not only meets rigorous safety standards but also comes with a warranty that underscores its reliability and long-lasting performance. This product is ideal for families looking to improve their water quality with a dependable, efficient, and user-friendly filtration system that aligns with modern needs and environmental considerations.