Installation instructions.

Plan How You Will Install the Softener

You must first decide how to run in and out pipes to the softener. Look at the house main water pipe at the point where you will connect the softener. Is the pipe soldered copper, glued plastic or threaded galvanized? What is the pipe size?

WARNING: Use only lead-free solder and flux to prevent lead poisoning.

See Typical Installation Illustration, Fig. 1. Use this as a guide when planning your particular installation. Be sure to direct the incoming hard water supply to the softener valve inlet fitting. The valve is marked IN and OUT. See illustration on page 5 to help you prepare.

Where to Install the Softener

Place the softener as close as possible to a sewer drain, or other acceptable drain point or standpipe.

It is recommended to keep outside faucets on hard water to save soft water and salt.

Do not install the softener in a place where it could freeze. Freeze damage is not covered by the warranty.

Do not install the softener where it would block access to the water heater or access to the main water shutoff.

Put the softener in a place where water damage is least likely to occur if a leak develops. The manufacturer will not repair or pay for water damage.

A 120-volt electric outlet is needed to plug in the included transformer. The softener has a 10 foot power cable. If the outlet is remote (up to 100 feet), use 18 gauge wire to connect. Be sure the electric outlet and transformer are in an inside location, to protect from wet weather. Be sure the outlet is unswitched to prevent accidental shutoff.

If installing in an outside location, you must take the steps necessary to assure the softener, installation plumbing, wiring, etc., are as well protected from the elements (sunlight, rain, wind, heat, cold), contamination, vandalism, etc., as when installed indoors.

Outdoor installation is not recommended, and voids the warranty.

Keep the softener out of direct sunlight.

The sun’s heat may distort non-metallic parts and may damage the electronics.

Tools and Materials Required for Installation

In and out fittings included with the softener are 3/4″ (nominal) copper sweat tubes.

You should maintain the same, or larger, pipe size as the water supply pipe, up to the softener inlet and outlet.

Use the included bypass valve to install the softener. The bypass valve allows you to turn off water to the softener for servicing, but still have water in the house pipes. The in and out fittings referred to above connect to the bypass valve with the included nuts and washers.

Use copper, brass or galvanized pipe and fittings. Some codes may also allow CPVC plastic pipes.

If additional drain hose is needed for valve and salt tank drains, it can be ordered from GE Parts at 800.626.2002.

If a rigid valve drain is needed to comply

with plumbing codes, you can buy the parts needed to connect a 1/2″ copper tubing or plastic pipe drain.

Clean nugget or pellet water softener salt is needed to fill the brine tank, see Step 8 in the Step-by-Step Installation Instructions.

4

Page 4
Image 4
GE GXSF31E installation instructions Plan How You Will Install the Softener, Where to Install the Softener

GXSF31E specifications

The GE GXSF31E is a state-of-the-art water filtration system that effectively addresses the need for clean and great-tasting water in residential applications. This model focuses on efficiency, reliability, and advanced filtration technologies that enhance water quality for everyday use.

One of the main features of the GE GXSF31E is its robust filtration capabilities. It utilizes a dual-stage filtration process that combines sediment filtration with activated carbon block technology. This dual approach not only removes common contaminants such as chlorine, sediment, and rust but also significantly improves the taste and odor of your water. As a result, users enjoy water that is not only safe but also refreshing and pleasant to drink.

In terms of capacity, the GE GXSF31E is designed to meet the needs of medium to large households. With a production capacity of up to 31,000 grains, it is capable of efficiently handling the water demands of families with multiple members. The system features a digital control panel that allows users to monitor and manage the filtration process effectively, providing alerts for filter replacements and ensuring optimal performance at all times.

The GE GXSF31E also incorporates advanced technologies for ease of maintenance. The unit is equipped with a self-cleaning mechanism that helps reduce the need for manual cleaning, thereby extending the lifespan of the filters and the system as a whole. This feature significantly enhances convenience, as homeowners can rely on the unit to maintain its efficiency without constant intervention.

Energy efficiency is another critical characteristic of the GE GXSF31E. The system is designed to operate with minimal energy consumption, making it an environmentally friendly choice for responsible consumers. Additionally, its compact design allows for easier installation and integration into limited spaces, which is particularly advantageous for urban settings.

The GE GXSF31E not only meets rigorous safety standards but also comes with a warranty that underscores its reliability and long-lasting performance. This product is ideal for families looking to improve their water quality with a dependable, efficient, and user-friendly filtration system that aligns with modern needs and environmental considerations.