Installation instructions.

Plan How You Will Install the Softener

You must first decide how to run in and out pipes to the softener. Look at the house main water pipe at the point where you will connect the softener. Is the pipe soldered copper, glued plastic or threaded galvanized? What is the pipe size?

WARNING: Use only lead-free solder and flux to prevent lead poisoning.

See Typical Installation Illustration, Fig. 1. Use this as a guide when planning your particular installation. Be sure to direct the incoming hard water supply to the softener valve inlet fitting. The valve is marked IN and OUT. See illustration on page 5 to help you prepare.

Where to Install the Softener

■Place the softener as close as possible to a sewer drain, or other acceptable drain point or standpipe.

■It is recommended to keep outside faucets on hard water to save soft water and salt.

■Do not install the softener in a place where it could freeze. Freeze damage is not covered by the warranty.

■Do not install the softener where it would block access to the water heater or access to the main water shutoff.

■Put the softener in a place where water damage is least likely to occur if a leak develops. The manufacturer will not repair or pay for water damage.

■A 120 volt electric outlet is needed to plug in the included transformer. The softener has a 10 foot power cable. If the outlet is remote (up to 100 feet), use 18 gauge wire to connect. Be sure the electric outlet and transformer are in an inside location, to protect from wet weather. Be sure the outlet is unswitched to prevent accidental shutoff.

■If installing in an outside location, you must take the steps necessary to assure the softener, installation plumbing, wiring, etc., are as well protected from the elements (sunlight, rain, wind, heat, cold), contamination, vandalism, etc., as when installed indoors.

Outdoor installation is not recommended and voids the warranty.

■Keep the softener out of direct sunlight.

The sun’s heat may distort non-metallic parts and may damage the electronics.

Tools and Materials Required for Installation

■In and out fittings included with the softener are 3/4″ (nominal) copper sweat tubes.

You should maintain the same, or larger, pipe size as the water supply pipe, up to the softener inlet and outlet.

■Use the included bypass valve to install the softener. The bypass valve allows you to turn off water to the softener for servicing, but still have water in the house pipes. The in and out fittings referred to above connect to the bypass valve with the included nuts and washers.

■Use copper, brass or galvanized pipe and fittings. Some codes may also allow CPVC plastic pipes.

■If additional drain hose is needed for valve and salt tank drains, it can be ordered from GE Parts at 800.626.2002.

■If a rigid valve drain is needed to comply

with plumbing codes, you can buy the parts needed to connect a 1/2″ copper tubing or plastic pipe drain.

■Clean nugget or pellet water softener salt is needed to fill the brine tank, see Step 8 in the Step-by-Step Installation Instructions.

4

Page 3 Page 5
Page 4
Image 4
GE GXSF35E, GXSF39E installation instructions Plan How You Will Install the Softener, Where to Install the Softener
Page 3 Page 5

GXSF39E, GXSF35E specifications

The GE GXSF35E and GXSF39E are sophisticated water filtration systems designed to meet the diverse needs of residential consumers. Offering reliable water purification solutions, these models efficiently remove impurities, ensuring clean and safe water for household use.

Both the GXSF35E and GXSF39E units feature advanced filtration technology, specifically designed to target a broad spectrum of contaminants, including chlorine, sediment, lead, and other harmful substances. The filtration process effectively enhances the taste and smell of drinking water, allowing families to enjoy fresh and clean water directly from their taps.

One of the standout features of these models is their high-capacity filtration capabilities. The GXSF35E boasts a 35,000-gallon capacity, making it suitable for medium to large households. Conversely, the GXSF39E, designed for larger families, offers an impressive 39,000-gallon capacity. This extended capacity ensures that users have access to purified water for an extended period, reducing the frequency of cartridge replacements and associated maintenance.

In terms of technical specifications, both models utilize a unique dual-stage filtration system. The first stage consists of a high-performance sediment filter that captures large particles and sediments, while the second stage employs an activated carbon filter that removes chemical contaminants and enhances taste. This two-tiered approach ensures comprehensive purification and longevity of the filter media.

Another major characteristic of the GXSF35E and GXSF39E is their user-friendly design. With features such as easy installation processes, intuitive control panels, and filter change indicators, these systems cater to users with varying levels of technical expertise. The compact design of the units allows for versatile installation options, whether in basements, under sinks, or in utility rooms.

Both models are also equipped with smart technology, enabling users to monitor filter life through mobile applications or digital displays. This connectivity feature ensures that homeowners are well-informed when it’s time to replace filters, enhancing the system's overall efficiency and effectiveness.

In conclusion, the GE GXSF35E and GXSF39E water filtration systems stand out in the market due to their efficient filtration technologies, high capacity, user-friendly features, and smart monitoring capabilities. They provide an excellent solution for families seeking safe and clean drinking water without the hassles associated with traditional filtration methods.
Top Page Image Contents