Manuals / GE / Kitchen Appliance / Range

GE JGBS18, JGBC18 On some models, you may have to remove an access cover also, Tools Required

Models: JGBC18 JGBS18

1 48

Download 48 pages 50.75 Kb

Page 40

HOW TO CONVERTA SEALED BURNER RANGE

FOR USE WITH 1P GAS OR NATUW GAS

This range leaves the factory set for use with natural gas. If you convert to LP gas, keep these instructions and orifices in case you want to convert back to natural gas.

The conversion should be done by a qualified technician or installer.

TOOLS REQUIRED:

1/2” open-end wrench

Flat blade screwdriver (small) Nut drivers: 9/32” or 7mm

❑pREpARE RANGE FOR CONVERSION

(1)Turn off gas supply at the wall.

(2)Turn off the electical power to the range.

If range has not yet been connected to gas supply, or if flexible connection was made, range maybe pulled out from the wall to make conversion easier.

❑CONVERT THE PRESSURE REGU~TOR

W~ING: Do not remove the pressure regulator from tie range.

1.Remove the storage drawer, broiler drawer or kick panel and locate the pressure regulator at rear of the range,

Remove Screws

Access Cover <m

On some models, you may have to remove an access cover also.

40

❑COHVERT THE PRESSURE REGU~TOR (continue~

this protective cap’	Cap Assembly
except for conversion

2.Unscrew the plastic-protected hex-nut cap from the regulator.

3.Carefully pry the protective plastic cap off the threaded metal cap. Gently pull the plastic washer off the threads on the other side of the metal cap.

4.Push the plastic cap onto the end of the metal

cap displaying the type of gas you are converting to. Press the attached plastic washer onto the threads on the other side of the metal cap.

5.Screw the hex-nut cap back into the regulator. Do not overtighten.

~CONVERTING SURFACE BURNERS

—Grate

1.Remove grates, burner caps and burner heads.

2.Remove the brass orifice

spud inside the chimney of each burner using a 9/32” or 7mm nut driver.

3.Install the orifice spuds Chi according to one of the following diagrams (see ❑

or ❑ ), for LP gas or natural gas, depending on

which you are converting to.

Orifi/e spud

Image 40

GE JGBS18 manual On some models, you may have to remove an access cover also, Tools Required, Convert the Pressure REGU~TOR

Contents

Safe~ Operating Instructions, TipsSave time and money. Before you request service Read this guide carefullyWrite down the model and serial numbers If you received a damaged rangeWhen You Get Your Range Using Your RangeWortant SAFE~ ~STRUCTIONS Always heat fat slowly, and watch as it heatsCleating Your Range Baking, Broiling and RoastingDo no$ leave any items on the cooktop Features of Your Range ~Sealed BurnersOven Light OtiOff Switch on some models Surface Burners, Grates and Drip Pans on some modelsOven Control Surface Burner Control KnobsTo Your OLD Om? Before Lighting a Burner Surface Burner ControlsTo Light a Surface Burner How to Select Flame Size After Lighting a BurnerTop-of-Range Cookware Can be dangerous. PlacingTo Set the Timer To Change or Cancel the Timer SettingDisplay Clock While Timer Is Operating TimerBefore Using Your Oven Power Outage -Electric IgnitionPower Outage -Stinding Pilot Oven ControlOven Shelves Shelf PositionsOven Vents Shelf on the shelf supportHow to Set Your Range for Baking Pan PlacementOven Shelves Arrange theoven ~ PreheatingBaking Guides CookiesAluminum Foil PiesAdjust the Oven Thewostat To Adjust the ThermostatDual Shelf Cooking Use of Aluminum FoilQuestions and Answers Frozen RoastsWhy are my meats not turning out as brown as they should? Should I salt the meat before broiling?BRO~~G GU~E ‘ediu1mw @’arg’I Sealed Burner Assemblies on some modelsStandard win Burners on some models Remove the grates and ~ lift out the drip pansCooktop Surface Burner GratesOven Bottom Oven Light Bulb on some models Control Panel and KnobsRemovable Broiler Drawer on some models Broiler Pan and GridRemovable Storage Drawer on some models Oven Air VentsRemovable Kick Panel on some models Lift-Off Oven Door To remove the door, uDo not immerse door in water Inside of door Outside of doorTo Clean the Continuous-Cleaning Oven Oven bottom has a porcelain enamel finishFor Your Safety JGBS04 JGBS06 JGBS07LM~RTANT Safety Instructions General PRovlDEADEQuATE GAS Supply Rigid Pipe HookupforModels Equipped with Sealed Burners Connect the Wnge to GX~~~~Ada,FN,eupfw ELECTRlmL Connections on some models GroundingELECTRl~L Connections Electric DisconnectManifold panel Light the PilotsLight the Pilots Check Ignition of Surface BurnersSutiace Burner Ignition Quali~ of FlamesTo remove the oven bottom To remove the burner btifle on some modelsAdjusting the AIR Adjustment Adjustable wrench to back Install the oven shelvesRange where it will be installed Oven racks. E using a spirit level, take twoOn some models, you may have to remove an access cover also Tools RequiredConvert the Pressure REGU~TOR ~ Converting Surface BurnersOrifice Spuds for Convetiing to Natural Gas Orifice Spuds for Converting to LPGasOven Burner Adjust LOW FME Setting YeUow flamesNormal for natural gas Check for L~KSAbout 2 turns With the base. To prevent damage, do not overtighten spudConvert AIR Adjustment Shutter Adjust Oven ThermostatWith baffle in place, flames Screw Surface knobs to LOW$URPACE RU~RS Light but Oven RAtiOW E~CT 800.626.2000 Consumer information serviceTimes oven is used. This is temporary Wdll Be There JGBS06 JGBS20 JGSS05 JGBS17 JGBS22 Jgbc JGBS04 JGBS18 JGBS23JGBS07