Manuals / Brands / Kitchen Appliance / Microwave Oven / GE / Kitchen Appliance / Microwave Oven

GE JNM1541SPSS B3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET, B4. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST

1 48

Download 48 pages, 3.4 Mb

Installation Instructions

To use toggle bolts:

Spacing for Toggles More

Than Wall Thickness

	Mounting	Toggle Wings
		Toggle
	Plate
		Bolt

Wall

Bolt End

3Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.

CAUTION:Be careful to avoid pinching fingers between the back of the mounting plate and the wall.

4Tighten all bolts. Pull the plate away from the wall to help tighten the bolts.

B3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws and a hole large enough for the power cord to fit through.

•Read the instructions on the TOP CABINET TEMPLATE.

•Tape it underneath the top cabinet.

•Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION:Wear safety goggles when drilling holes in the cabinet bottom.

B4. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST

1Remove and save the screw that holds the blower motor door closed on the back and the blower retaining screw on the top of the door.

Blower

Retaining		Blower
Retaining
Screw
		Blower Motor
	Back of	Door Retaining
	Back of	Screw
	Microwave	Screw
	Microwave
	Oven

2Open the blower door by lifting it up at the back of the microwave oven. Remove and save the blower retaining screw.

Blower Retaining

Screw

3Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit.

	BEFORE: Fan Blade	End B
	Openings Facing Up	End B
	Openings Facing Up

End A

16

Contents

• Note to Consumer – Keep these Note to Installer – CONTENTS General information Step-by-stepinstallation guide Page OUTSIDE TOP EXHAUST (EXAMPLE ONLY) OUTSIDE BACK EXHAUST (EXAMPLE ONLY) Exhaust connection: Maximum duct length: Elbows, transitions, wall and roof caps, etc HARDWARE PACKET ADDITIONAL PARTS Page A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE B. FINDING THE WALL STUDS C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position – beneath flat bottom cabinet Plate position – beneath framed recessed cabinet bottom Plate position – beneath recessed bottom cabinet with front overhang D. ALIGNING THE WALL PLATE Set the mounting plate aside AOUTSIDE TOP EXHAUST (VERTICAL DUCT) BOUTSIDE BACK EXHAUST (HORIZONTAL DUCT) CRECIRCULATING (NON-VENTEDDUCTLESS) (Vertical Duct) INSTALLATION OVERVIEW A1. ATTACH THE MOUNTING PLATE TOTHE WALL To use toggle bolts: A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET A4. MOUNT THE MICROWAVE OVEN (cont.) A5. ADJUST THE EXHAUST ADAPTOR A6. CONNECTING DUCTWORK B1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST B3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET B4. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.) Page C2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET C3. ADAPTING MICROWAVE BLOWER FOR RECIRCULATION C3. ADAPTING MICROWAVE BLOWER FOR RECIRCULATION (cont.) C4. MOUNT THE MICROWAVE OVEN C4. MOUNT THE MICROWAVE OVEN (cont.) C5. INSTALLING THE CHARCOAL FILTER Page Page Nota para el consumidor – Guarde estas Nota para el instalador – Asegúrese de dejar CONTENIDO Información general Guía de instalación paso por paso Page ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE) ESCAPE POSTERIOR EXTERNO (EJEMPLO SOLAMENTE) Conexionesde escape: Longitud máxima del conducto: PAQUETE DE ELEMENTOS PARTES ADICIONALES Page B. CÓMO ENCONTRAR LOS POSTES DE VIGA EN LA PARED C.CÓMO DETERMINAR LA LOCALIZACIÓN DEL PLATO DE MONTAJE DEBAJO DE SU GABINETE Posición del plato – debajo de gabinetes de fondo plano Posición del plato – debajo de gabinetes de fondo apoyado en un marco Posición del plato – debajo de gabinetes de fondo apoyado con frente saliente D. CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Aparte el plato de montaje ESCAPE POSTERIOR EXTERIOR CRECIRCULACIÓN (SIN CONDUCTO DE VENTILACIÓN) A1. CÓMO ADHERIR EL PLATO DE MONTAJE A LA PARED A2. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE A5. CÓMO AJUSTAR EL ADAPTADOR DE ESCAPE B2. CÓMO ADHERIR EL PLATO DE MONTAJE A LA PARED B3. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE B4. CÓMO ADAPTAR EL CALEFACTOR DEL MICROONDAS PARA EL ESCAPE POSTERIOREXTERIOR DEL MICROONDAS PARA EL ESCAPE POSTERIOR EXTERIOR B5. CÓMO MONTAR EL HORNO MICROONDAS C1. CÓMO ADHERIR EL PLATO DE MONTAJE A LA PARED C2. USE LA PLANTILLA DE GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE C3. CÓMO ADAPTAR EL CALEFACTOR DEL MICROONDAS PARA C3. CÓMO ADAPTAR EL CALEFACTOR DEL MICROONDAS PARALA RECIRCULACIÓN (continuación) C4. CÓMO MONTAR EL HORNO MICROONDAS IMPORTANTE: Si no se usan bloques de relleno, podrían ocurrir daños por apretar C4. CÓMO MONTAR EL HORNO C5. CÓMO INSTALAR EL FILTRO DE CARBONILLA