GE ADT520 Select Options Continued, Start Dishwasher, Cycle Completion, Steam, Prewash

Models: ADT520 Series GDT530-550 Series GDF510-540

1 48
Download 48 pages 55.77 Kb
Page 5
Image 5

 

 

 

GEAppliances.com

 

 

Select Options (Continued)

5

 

 

Steam

For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected PRIOR to

 

 

 

 

(Prewash)

starting the cycle. The Steam option adds approximately 30 minutes to the cycle time. This option is

 

 

(on some models)

available with Heavy, Auto Sense, and Normal cycles.

 

 

Wash

Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This will

 

 

Zones

shorten the cycle time and conserve energy. This option can be used when there is only half a

 

 

(on some models)

load of dishes.

 

 

Delay

Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to select

 

 

Hours

the number of hours, then press Start one time to begin countdown. The cycle will start once allotted time

 

 

(on some models)

has expired.

 

 

 

 

 

 

Control

You can lock the controls to prevent selections from being made. You can also lock the controls

 

 

Lock

after you have started a cycle to prevent cycle changes. For example, children cannot accidentally

 

 

 

start the dishwasher by pressing pads with this option selected.

 

 

 

To LOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 seconds or

 

 

 

press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light will turn

 

 

 

on to indicate the control is locked.

 

 

 

To UNLOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 second

 

 

 

or press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light

 

 

 

will turn off to indicate the control is unlocked.

 

 

 

 

 

 

Energy

When connected to a smart meter and your electric company, the dishwasher will automatically delay starting

 

 

Smart

a cycle during the more expensive peak demand times, and run when demand is low. However, you can override

 

 

 

the delay settings and use the dishwasher as needed. Learn more about Energy Smart under the Using the

 

 

 

Dishwasher section.

 

 

 

 

 

Start Dishwasher

6

 

 

 

Start

Door can be open to select the desired options. Press the Start pad and close the door within 10 seconds

 

 

 

to start the cycle or begin the Delay Hours countdown. The wash cycle will begin shortly after closing

 

 

 

the door. If the door is open, the illuminated lights will turn off if a pad is not pressed within two minutes.

 

 

 

To activate the display, close and open the door or press any pad.

 

 

 

 

 

 

Interrupt

To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash cycle to

 

 

or Pause

pause. The dishwasher will beep every minute to remind you to close the door. To restart or resume

 

 

 

the cycle, press Start, and close the door.

 

 

Cancel

To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door. The dishwasher will drain,

 

 

 

emit a beep sound, and the wash cycle light will turn OFF.

 

 

 

 

 

Cycle Completion

7

 

 

 

Sanitized

Displayed at the end of the cycle when Wash Temp Sani (Sanitize) has been selected and the dishwasher

 

 

 

has met the requirements for sanitization. See Wash Temp Sani, for complete option description.

 

 

 

Opening the door or pressing any key while the door is closed will turn off the light.

 

 

 

 

 

 

Clean

Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean. Opening

 

 

 

the door or pressing any key while the door is closed will turn the light off.

5

Page 5
Image 5
GE ADT520, Series GDF510-540 owner manual Select Options Continued, Start Dishwasher, Cycle Completion, Steam, Prewash