GE ZISW420DM specifications Monogram, The Installation Space, Water And Electrical Locations

Models: ZISW420DM

1 6
Download 6 pages 18.37 Kb
Page 1
Image 1
Monogram.™

Monogram.

ZISW420DM – GE Monogram 42" Built-In Refrigerator with Dispenser and Water Filter

THE INSTALLATION SPACE

42" Models 18"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

41-1/2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

84 1/2" max

Electrical

 

 

 

 

 

 

 

 

 

 

 

Area

5"

 

 

 

 

83 1/2" min

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Finished

 

 

 

 

 

 

 

 

 

 

 

 

74" From Floor

Opening

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24"

 

 

 

 

 

 

 

 

 

 

to Bottom

 

 

 

 

 

 

 

 

 

 

 

 

 

of Electrical

 

 

 

5"

 

Water Supply

5"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 1/2"

 

THE INSTALLATION SPACE3 1/2"

41"

Case Width

 

*84" From

*83-1/2"

Floor to

Top Frame

at

Rear

 

42"

Frame to Frame

*Shipping height. The refrigerator can be adjusted to fit into a cutout that is 83-1/2” min. to

84-1/2” max. height. Note that the top case trim at the front is 1/2” higher and will overlap upper cabinetry or soffit. Use leveling legs and wheels for height adjustment.

Water And Electrical Locations

The opening must be prepared with the electrical and water supply located as shown.

The cutout depth must be 24".

Designed for industry standard flush installation. The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation.

The cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.

Frameless cabinets:

The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.

Additional Specifications

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

Water line can enter the opening through the floor or back wall. The water line should be 1/4" O.D. copper tubing between the cold water line and water connection location, long enough to extend to the front of the refrigerator. Installation of an easily accessible shut off valve in the water line

is recommended.

Specification Revised 8/03

Product Clearances

These refrigerators are equipped with a 2 position door stop. The factory set 130° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.

130° Door Swing

90° Door Swing

Water And Electrical Locations 13"The cutout depth must be 24".The cutout depth beneath a soffit:19" Frameless cabinets:

23-7/8" Behind Frame

26-5/8"

Allow minimum clearances for freezer door and fresh food door for a full 130° door swing and to allow for pan removal.

4" minimum clearance is required when door swing is adjusted to 90°. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.

Listed by

Underwriters

As an ENERGY STAR® Partner,

R LaboratoriesGE has determined that this product meets the ENERGY STAR®

guidelines for energy efficiency.

For answers to your Monogram,® GE Profileor

GE appliance questions, visit our website at

GEAppliances.com or call

GE Answer Center® service, 800.626.2000.

110176

Page 1
Image 1
GE ZISW420DM specifications Monogram, The Installation Space, Water And Electrical Locations, The cutout depth must be