|
|
|
| ge.com |
|
|
| Options |
|
3 |
|
| ||
|
|
| The light above the selected pad will be ON to indicate which OPTION has been selected. | |
|
|
| ||
|
|
| HOT START | For use with heavily soiled and/or |
|
|
| (on some models) | PRIOR to starting the cycle. This option will improve both wash and dry performance. This |
|
|
|
| option adds 20 minutes to the cycle time. |
|
|
|
| NOTE: Cannot be selected with RINSE ONLY cycle. |
|
|
|
|
|
|
|
| HEATED DRY | Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry, |
|
|
| Light OFF | you can prop the door open after the CLEAN light illuminates. |
|
|
|
|
|
|
|
| HEATED DRY | Turns the heater on for fast drying. This will extend the total run time by 38 minutes. |
|
|
| Light ON | NOTE: Cannot be selected with RINSE ONLY cycle. |
|
|
|
|
|
|
|
| LOCK | You can lock the controls to prevent any selections from being made. Or you can lock the |
|
|
|
| controls after you have started a cycle. |
|
|
|
| Children cannot accidentally start dishwasher by touching pads with this option |
|
|
|
| selected. |
|
|
|
| To LOCK the dishwasher control, touch and hold the HEATED DRY pad for 3 seconds. The light below the |
|
|
|
| HEATED DRY pad will turn on. To UNLOCK the dishwasher control, touch and hold the HEATED DRY pad for |
|
|
|
| 3 seconds. The LOCK light will turn off. |
|
|
|
|
|
|
|
| HOT WASH | When selected, the cycle will run longer with the heating element on to improve both wash and |
|
|
|
| dry performance. NOTE: Cannot be selected with RINSE ONLY cycle. |
|
|
|
|
|
|
|
| DELAY HOURS | You can delay the start of a wash cycle for up to 8 hours. Touch the DELAY HOURS |
|
|
|
| pad to choose the number of hours you want to delay the start of the cycle; then touch |
|
|
|
| START/RESET one time. The dishwasher will count down and start automatically at the correct |
|
|
|
| time. Touching START/RESET a second time will cancel the DELAY START selection. |
|
|
|
|
|
|
|
| RESET | To change a cycle after washing starts, touch the START/RESET pad to cancel the cycle. |
|
|
|
| The START/RESET light will flash while the water is pumped out if needed. This takes |
|
|
|
| approximately 90 seconds. When the light stops flashing, the dishwasher can be |
|
|
|
| reprogrammed and restarted. |
4 |
| Start |
| |
Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the START/RESET pad once to begin the cycle. Water begins to fill the dishwasher, and approximately 60 seconds later the wash action begins. Touching the START/RESET pad a second time will cancel the cycle and cause the water to drain out. This will take approximately 2 minutes.
NOTE: The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the dishwasher door is fully closed, the control panel lights will display the last settings you selected.
If you don’t want to change any of the settings, simply touch the START/RESET pad once to begin the cycle.
If the door is closed, the indicator lights will turn off if the START/RESET pad is not pressed within two minutes. To activate the display, open and close the door or touch any pad.
Also, if a power failure occurs, NORMAL and HEATED DRY will automatically be programmed.
7
Safety Instructions
Operating Instructions
Troubleshooting Tips
Consumer Support
