OPERATING INSTRUCTIONS
1.Make sure that the VOLTAGE SELECTOR SLIDE SWITCH (18), found on the rear panel, is set for the proper voltage. Plug the unit in and press the POWER SWITCH (1). The unit will turn on. Pushing the POWER SWITCH (1) a second time will turn the unit off.
2.Press the OPEN/CLOSE BUTTON (3), place a CD in the DISC TRAY (2) and press the OPEN/CLOSE BUTTON (3) again. The tray will close into the unit. The display will initially show the number of tracks and the total time of the CD.
3.Push the TRACK SKIP BUTTONS (6) to select the track you want to play.
4.Press the PLAY/PAUSE BUTTON (7) and the unit will instantly play.
CUE INSTRUCTIONS
1.To start the play at a point other than the beginning of a track, follow these instructions:
First choose the track you wish to play, and then press the PLAY/ PAUSE BUTTON (7) so the unit goes into the play mode. Press the PLAY/PAUSE BUTTON (7) to pause play at the spot where you want the play to start the CUE POINT. Use the SEARCH BUTTONS (8) to pick the precise spot you want play to begin, then press the PLAY/PAUSE BUTTON (7) again to save the cue point. Press the CUE BUTTON (5) to pause play at the cue point (the unit will go into the pause mode and the location indicated on the display will be the memorized cue point). You can preview the cue point by pressing and holding down the CUE BUTTON (5). Press the PLAY/PAUSE BUTTON (7) to begin play from the cue point.
2.Once you have saved a cue point you can fine tune or change the memorized cue point:
To change a cue point, push the PLAY/PAUSE BUTTON (7) so the unit plays from the cue point, then press the PLAY/PAUSE BUTTON (7) at the spot you wish your new cue point. Press the PLAY/PAUSE BUTTON (7) again to save the cue point. The unit will go into the pause mode and the location indicated on the display will be the new memo- rized cue point.
To fine tune a cue point, pause play at the memorized cue point, then use the SEARCH BUTTONS (8) to scan frame by frame (1/75th of a second) to where you want play to begin. Press the PLAY/PAUSE BUTTON (7) to save the new cue point.
Note: During fine tuning there will be a stutter effect (to help you find the beat). The stuttering effect will end when you press the PLAY/PAUSE BUTTON (7) to save the cue point. Also, during fine tuning if you hold down the SEARCH BUTTONS (8), the unit will scan quickly after 10 frames.
ROBO START INSTRUCTIONS
IN SINGLE-AUTO CUE MODE:
Use ROBO START in
1.Engage
2.Press the ROBO START (15) button to activate ROBO START (the button will blink). Play will alternate between the two sides of the CD player. At the end of the track, the playing side will pause, and the other side will play. At the end of this track, the playing side will pause, and the other side will play. The CD player will continue to alternate between the two sides until you stop it (after the last track of the CD, it goes back to the first track).
NOTE: Pausing the playing side in the middle of a track will cause
the other side to play. When that track ends, play will begin from the middle of the track where play was paused.
IN CONTINUOUS MODE OR DURING NORMAL PLAY:
If you use ROBO START without
1.During normal play, set a cue point on the other side of the CD player.
2.Press the ROBO START (15) button to activate ROBO START (the button will blink).
3.Press PLAY/PAUSE BUTTON (7) on the playing side to begin play from the cue point on the other side.
TROUBLE SHOOTING
•If the disk will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for excessive dirt, scratches, etc.
•If the disc turns but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver.
•If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CDs are recorded out of spec and will skip on most or all CD players. Before sending the unit in for repair, try playing a CD that you are sure plays properly.
SPECIFICATIONS
GENERAL: |
|
|
|
|
| |
Type |
|
| Compact Disc Player | |||
Disc Type |
| Standard Compact discs (12 cm & 8 cm) | ||||
Time Display | Track Elapsed, Track Remain, or Total remain | |||||
Variable Pitch |
| +/- 16% | ||||
Pitch Bend | .......................................................................... |
| +/- 16% | |||
Start |
|
| Within 0.02 seconds | |||
Track | Selection | 1 to | 99 Tracks | |||
AUDIO SECTION: |
|
|
|
| ||
Quantization | 1 Bit Linear/Channel, 3 Beam Laser | |||||
Oversampling Rate |
| 8 Times | ||||
Sampling | Frequency | 44.1 | kHz | |||
Frequency | Response | 20 Hz to 20 kHz | ||||
Digital Output |
| IEC958 | ||||
Total Harmonic Distortion | Less Than 0.05% | |||||
Signal | to | Noise | Ratio | >96 | dB | |
Dynamic Range |
| >94 dB | ||||
Output Level (nominal) | 1.9 Volts R.M.S. | |||||
Power | Supply | AC 115/230V, | 60/50 | Hz | ||
Dimensions | ............................... | 19” x 10.5” x 3.5” (483 x 267 x 90 mm) | ||||
Weight |
|
|
| 9 lbs. (4 kg) | ||
*Specifications and design are subject to change without notice for purpose of improvement.
Page 4
