![](/images/new-backgrounds/1242693/2426939x1.webp)
CDX-2200
press PGM and the
11 SINGLE: Pressing the SINGLE button engages SINGLE mode, in this mode the
12TIME: The TIME button switches the time display between three available sources, these three are TIME ELAPSED on the track, TOTAL REMAIN on the disc and REMAIN on the track. TIME ELAPSED indicates how much time has cur- rently gone by since the play button was pressed, TIME RE- MAING ON DISC will count down the time remaining on the entire disc and TIME REMAINING ON TRACK counts down the time that is left before the end of the track.
13PITCH: Press the PITCH button to activate the PITCH CON- TROL SLIDE. Pitch range that can be controlled through the use of the PITCH CONTROL SLIDER. Press the PITCH but- ton again to deactivate this mode.
14PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE up or down will change the pitch percentage +/ - 12%.
15PITCH BEND: Pushing the PITCH BEND BUTTONS will au- tomatically raise the pitch up to +16% or lower the pitch down to
16LOOP SECTION: A LOOP repeats the section between the entry point (LOOP IN) and the exit point (LOOP OUT).
A.To set a loop while the unit is playing, start by pressing the LOOP IN BUTTON (it will light up)
B.When you reach the desired end loop point press the LOOP OUT BUTTON (it will also light up). The LOOP IN and LOOP OUT buttons will blink. The loop will continue playing until you press the LOOP OUT BUTTON again allowing the music to continue from that point on.
C.To
D.When you have released your loop the LOOP IN and LOOP OUT BUTTON buttons will turn OFF and the will remain lit to indicate that your loop is stored in the CDX- 2200 memory.
E.Pressing the LOOP IN BUTTON again while the unit is playing will erase the previously saved loop while saving your new loop entry point.
F.Press LOOP OUT to exit the loop and save a new com- plete loop.
G. Press RELOOP to return to the beginning of the previ- ously saved loop from normal play. Press RELOOP repeat- edly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POINT, WHILE ALL OTHERS WILL BE SEAMLESS.
17PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON causes the operation to change from PLAY to PAUSE or from PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit when in PLAY mode, while it blinks in PAUSE mode.
18CUE: To set a CUE point, press the PLAY / PAUSE BUTTON while a file is playing, and use the JOG WHEEL to adjust the file to a desired point in the track. Pressing the PLAY / PAUSE
BUTTON will set a CUE point. While the unit is playing and after the cue point has been programmed, pressing CUE will cause the CD player to enter the PAUSE mode (PLAY/PAUSE BUTTON blinks) at the programmed cue point (the CUE LED is lit). Holding down the CUE button changes the function to preview, and allows you to stutter start or play from the pro- grammed CUE POINT. Releasing the CUE button will return the CD to the preset CUE point.
19TRACK SEARCH: The TRACK SEARCH buttons let you se- lect the track to play. +10 allows you to scan through the track selection in increments of 10.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING OF THE NEWLY SELECTED TRACK.
TROUBLESHOOTING:
- If a disc will not play, check to see if the disc was loaded cor- rectly (label side up). Also check the disc for excessive dirt, scratches, etc.
- If the disc turns but there is no sound, check the cable con- nections, if they are ok, check your amplifier or receiver.
5