Integrated Peripherals, USB Controller | Gigabyte GA-8I845GE775-G

Integrated Peripherals

English

2-3	Integrated Peripherals

		CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
				Integrated Peripherals
	On-Chip Primary PCI IDE			[Enabled]		Item Help
	On-Chip Secondary PCI IDE			[Enabled]		Menu Level `
	IDE1 Conductor Cable			[Auto]
	IDE2 Conductor Cable			[Auto]		If a hard disk
	USB Controller			[Enabled]		controller card is
	USB Keyboard Support			[Disabled]		used, set at Disabled
	USB Mouse Support			[Disabled]
	AC97 Audio			[Auto]		[Enabled]
	Onboard H/W LAN			[Enabled]		Enable onboard IDE
	Onboard LAN Boot ROM			[Disabled]		PORT
	Onboard Serial Port 1			[3F8/IRQ4]
	Onboard Serial Port 2			[2F8/IRQ3]		[Disabled]
	Onboard Parallel Port			[378/IRQ7]		Disable onboard IDE
	Parallel Port Mode			[SPP]		PORT
x ECP Mode Use DMA				3
KLJI: Move		Enter: Select		+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults		F7: Optimized Defaults

	On-Chip Primary PCI IDE
	Enabled		Enable onboard 1st channel IDE port. (Default value)
	Disabled		Disable onboard 1st channel IDE port.
	On-Chip Secondary PCI IDE
	Enabled		Enable onboard 2nd channel IDE port. (Default value)
	Disabled		Disable onboard 2nd channel IDE port.
	IDE1 Conductor Cable
	Auto		BIOS autodetects IDE1 conductor cable .(Default Value)
	ATA66/100		Set IDE1 Conductor Cable to ATA66/100 (please make sure your IDE
			device and cable are compatible with ATA66/100).
	ATA33		Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	IDE2 Conductor Cable
	Auto		BIOS autodetects IDE2 conductor cable. (Default Value)
	ATA66/100		Set IDE2 Conductor Cable to ATA66/100(please make sure your IDE
			device and cable are compatible with ATA66/100)
	ATA33		Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	USB Controller
	Enabled		Enable USB Controller. (Default value)
	Disabled		Disable USB Controller.
	USB Keyboard Support
	Enabled		Enable USB Keyboard Support.
	Disabled		Disable USB Keyboard Support. (Default value)

GA-8I845GE775-G Motherboard

- 34 -

Image 34

Gigabyte GA-8I845GE775-G Integrated Peripherals, On-Chip Secondary PCI IDE, IDE1 Conductor Cable, IDE2 Conductor Cable

Contents

Intel Pentium 4 LGA775 Processor Motherboard GA-8I845GE775-GUsers Manual Rev. 1001 12ME-I845GETG-1001 Motherboard MotherboardGA-8I845GE775-G April 22 GA-8I845GE775-G Copyright Product Manual Classification Table of Contents 4-1-1 Chapter 3 Drivers InstallationChapter 4 Appendix 4-1-2 GA-8I845GE775-G Motherboard Layout Block Diagram Page Installation Notices Chapter 1Hardware Installation1-1 Considerations Prior to Installation Instances of Non-Warranty 1-2 Feature Summary BIOS 1-3 Installation of the CPU and Heatsink 1-3-1 Installation of the CPU 1-3-2 Installation of the Heatsink 1-4 Installation of Memory notch DDR memory module 1-5 Installation of Expansion Cards Parallel Port PS/2 Keyboard and PS/2 Mouse Connector1-6 I/O Back Panel Introduction Serial Port COMA 1-7 Connectors Introduction 111 2010 1/2 ATX12V / ATX Power ConnectorPin No 5 FDD FDD Connector 3/4 CPUFAN / SYSFANCooler Fan Power ConnectorSYSFAN CD-L 6 IDE1/2 IDE Connector7 CDIN CD In Connector CD-R Power 8 FPANEL Front Panel JumperReset Switch IDE Hard Disk Active LED 10 SPDIFIO SPDIF In/ Out 9 FAUDIO Front Audio Panel ConnectorRear Audio R/ Return R 11 SURCEN Surround Center Connector 12 F USB1 Front USB Connector 13 COMB COMB Connector 14 CI Chassis Intrusion, Case Open 16 BATBattery 15 CLRCMOS Clear CMOS English CONTROL KEYS Chapter 2 BIOS SetupStatus Page Setup Menu / Option Page Setup Menu Main Menu „ Advanced BIOS Features The Main Menu Example BIOS Version F1„ Standard CMOS Features „ Power Management Setup „ Save & Exit Setup „ Set Supervisor Password„ Set User Password „ Exit Without Saving Time Standard CMOS FeaturesDate IDE Primary Master, Slave /IDE Secondary Master, Slave Halt on Drive A / Drive BFloppy 3 Mode Support for Japan Area Memory First / Second / Third Boot Device Advanced BIOS FeaturesBoot Up Floppy Seek Limit CPUID Max. to Password CheckCPU Hyper-Threading No-Execute Memory ProtectNote IDE1 Conductor Cable Integrated PeripheralsOn-Chip Secondary PCI IDE IDE2 Conductor Cable AC97 Audio Onboard LAN Boot ROMUSB Mouse Support Onboard H/W LAN Resume by Alarm Power Management SetupPower LED in S1 State ACPI Suspend Type KB Power ON Password Power On By MousePower On By Keyboard AC BACK Function PCI2 IRQ Assignment PnP/PCI ConfigurationsPCI1/5 IRQ Assignment PCI3 IRQ Assignment Current VoltageV Vcore / DDR25V / +3.3V / +12V PC Health StatusCase Opened Current CPU Temperature CPU Host Clock Control Frequency/Voltage ControlCPU Clock Ratio CPU Host Frequency Mhz Memory Frequency Mhz Top PerformanceHost/DRAM Clock ratio PCI/AGP Frequency Mhz Load Fail-Safe Defaults 2-10 Load Optimized Defaults Set Supervisor/User Password 2-11 2-12 Save & Exit Setup 2-13 Exit Without Saving Chapter 3Drivers Installation 3-1 Install Chipset Drivers 3-2 Software Application 3-3 Software Information This page lists all device you have for this motherboard 3-4 Hardware Information3-5 Contact Us Please see the last page for details English How to use the Xpress Recovery 4-1-1 Xpress Recovery IntroductionWhat is Xpress Recovery ? Chapter 4 Appendix F9 For Xpress Recovery Intel 865PE AGPSet BIOS for 8IPE1000MT F1 Check System Health OK 2. Execute Restore Utility 1. Execute Backup Utility Press B to Backup your System or Esc to Exit This program will recover your system to factory default Method 1 Q-FlashTM Utility 4-1-2 Flash BIOS Method IntroductionUpdating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards Before You Begin Entering the Q-FlashTM utility Exploring the Q-FlashTM / Dual BIOS utility screenTask menu for Dual BIOS utility Task menu for Q-Flash utility disk Using the Q-FlashTM utilitySteps stage BIOS, too 3. Press Y button on your keyboard after you are sure to update BIOSPlease do not take out the floppy disk when it begins flashing BIOS The BIOS file becomes Fba after updating Part Two Updating BIOS with Q-FlashTM Utility on Single-BIOS MotherboardsPress Y on your keyboard to save and exit Exploring the Q-FlashTM utility screen Are you sure to RESET ? Congratulation!! You have updated BIOS successfullyCopy BIOS completed - Pass at this stage Method 2 @BIOSTM Utility 1. Methods and steps 2. Note Stereo Speakers Connection and Settings 4-1-3 2- / 4- / 6-/ 8- Channel Audio Function Introduction 4 Channel Audio Setup 6 Channel Audio Setup Mic In Center/Subwoofer Speaker Out 8 Channel Audio Setup requires Audio Combo Kit, optional device Surround-Kit connector SPDIF cable connector English SPDIF Output Device Optional Device Note1 UAJ Introduction Enable UAJ functionYou can click UAJ Automatic button to enable UAJ function 4-2 Troubleshooting 10 beeps CMOS shutdown register read/write error English Appendix English TEL +886-2-8912-4888 Contact UsAddress No.6, Bau Chiang Road, Hsin-Tien, Taipei 231, Taiwan G.B.T. INC TEL+1-626-854-9338 China