Goodman Mfg GKS9 service manual Furnace Specifications, Model

FURNACE SPECIFICATIONS

MODEL	GKS9	GKS9	GKS9	GKS9	GKS9	GKS9
	0453BX*	0703BX*	0704CX*	0904CX*	0905DX*	1155DX*
Btuh
Input (US)	46,000	69,000	69,000	92,000	92,000	115,000
Output (US)	42,800	64,400	63,900	86,000	86,000	106,500
Input (CAN)	46,000	69,000	69,000	92,000	92,000	115,000
Output (CAN)	42,800	64,400	63,900	86,000	85,300	106,500
A.F.U.E.	92.1%	92.1%	92.1%	92.1%	92.1%	92.1%
Rated External Static (" w.c.)	.20 - .50	.20 - .50	.20 - .50	.20 - .50	.20 - .50	.20 - .50
Temperature Rise (°F)	35 - 65	35 - 65	35 - 65	35 - 65	35 - 65	35 - 65
ID Blower Pressure Switch Trip Point (" w.c.)	-1.20	-1.10	-1.10	-0.95	-0.75	-1.10
Blower Wheel (D" x W")	10 x 8	10 x 8	10 x 10	10 x 10	11 x 10	11 x 10
Blower Horsepower	1/3	1/3	1/2	1/2	3/4	3/4
Blower Speeds	4	4	4	4	4	4
Max CFM @ 0.5 E.S.P.	1200	1200	1600	1600	2000	2000
Power Supply	115-60-1	115-60-1	115-60-1	115-60-1	115-60-1	115-60-1
Minimum Circuit Ampacity (MCA)(1)	9.4	9.4	13.8	13.8	13.2	13.2
Maximum Overcurrent Device(2)	15.0	15.0	15.0	15.0	15.0	15.0
Transformer (VA)	40	40	40	40	40	40
Primary Limit Setting (°F)	150	160	160	150	160	170
Auxiliary Limit Setting (°F)	150	150	150	150	150	160
Rollout Limit Setting (°F)	200	200	200	200	200	200
Fan Delay On Heating	30 secs.	30 secs.	30 secs.	30 secs.	30 secs.	30 secs.
Off Heating	150 secs.	150 secs.	150 secs.	150 secs.	150 secs.	150 secs.
Fan Delay On Cooling	6 sec.	6 sec.	6 sec.	6 sec.	6 sec.	6 sec.
Off Cooling	45 secs.	45 secs.	45 secs.	45 secs.	45 secs.	45 secs.
Gas Supply Pressure (Natural/Propane) ("w.c.)	7 / 11	7 / 11	7 / 11	7 / 11	7 / 11	7 / 11
Manifold Pressure (Natural/Propane) ("w.c.)	3.5 / 10	3.5 / 10	3.5 / 10	3.5 / 10	3.5 / 10	3.5 / 10
Orifice Size (Natural/Propane)	43 / 55	43 / 55	43 / 55	43 / 55	43 / 55	43 / 55
Number of Burners	2	3	3	4	4	5
Vent Connector Diameter (inches) (3)	2	2	2	2	2	2
Combustion Air Connector Diameter (inches) (4)	2	2	2	2	2	2
Shipping Weight (lbs.)	132	135	153	158	170	175

(1)Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes.

(2)Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

(3)See Installation Instructions for appropriate vent diameter, length and number of elbows.

(4)See Installation Instructions for appropriate combustion air pipe diameter, length and number of elbows.

NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and wires in accordance with all national and/or local electrical codes. Use copper wire only.

1.These furnaces are manufactured for natural gas operation. Optional kits are available for conversion to propane operation.

2.For elevations above 2000 feet the rating should be reduced by 4% for each 1000 feet above sea level. The furnace must not be derated, orifice changes should only be made if necessary for altitude.

3.The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufacturers method or in accordance with the "A.S.H.R.A.E. GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the AIR CONDITIONING CONTRACTORS OF AMERICA. The total heat loss calculated should be equal to or less than the heating capacity. Output based on D.O.E. test procedures, steady state efficiency times output.

4.Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.

Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information.

11