Goodman Mfg SS-GME8 dimensions Airflow Data, Product Specifications

Product Specifications

Airflow Data

(CFM & Temperature Rise vs. External Static Pressure)

	Motor	Tons					External Static Pressure, (Inches Water Column)
Model
				0.1		0.2			0.3			0.4			0.5		0.6	0.7	0.8
	Speed	AC¹
			CFM		Rise	CFM	Rise	CFM		Rise	CFM		Rise	CFM		Rise	CFM	CFM	CFM
	T1	1½	875		59	793	65	736		70	674		77	592		88	556	509	460
GME8	T2	2	1,032		50	965	54	914		57	861		60	810		64	756	712	659
	T3	2½	1,217		43	1,153	45	1,098		47	1,051		49	1,009		51	964	918	877
0703BXC*
	T4	3	1,365		38	1,313	39	1,268		41	1,221		42	1,172		44	1,129	1,086	1,054
	T5	3½	1,549		33	1,505	34	1,460		36	1,420		37	1,378		38	1,350	1,305	1,268
	T1	2½	1,268		53	1,198	56	1,151		58	1,092		61	1,041		64	988	932	883
GME8	T2	3	1,362		49	1,305	51	1,261		53	1,212		55	1,170		57	1,121	1,074	1,021
	T3	3½	1,576		42	1,519	44	1,473		45	1,426		47	1,398		48	1,341	1,290	1,252
0905CXC*
	T4	4	1,755		38	1,711	39	1,657		40	1,627		41	1,579		42	1,548	1,502	1,463
	T5	5	2,183		31	2,128	31	2,094		32	2,060		32	2,014		33	1,992	1,944	1,847
	T1	3	1,466		58	1,415	60	1,357		63	1,306		65	1,248		68	1,202	1,144	1,088
GME8	T2	3½	1,642		52	1,596	53	1,552		55	1,499		57	1,449		59	1,388	1,352	1,306
	T3	4	1,750		49	1,750	49	1,707		50	1,667		51	1,610		53	1,574	1,531	1,486
1155CXC*
	T4	4	1,870		46	1,805	47	1,782		48	1,737		49	1,701		50	1,656	1,606	1,571
	T5	5	2,297		37	2,297	37	2,224		38	2,106		40	2,014		42	1,896	1,813	1,669

¹ @ 0.5” ESP

Notes

•CFM in chart is without filter(s). Filters do not ship with this furnace, but must be provided by the installer. If the furnace requires two return filters, this chart assumes both filters are installed.

•All furnaces ship as high-speed cooling and medium-speed heating. Installer must adjust blower cooling and heating speed as needed.

•For most jobs, about 375 - 400 CFM per ton when cooling is desirable.

•INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPECIFIED ON THE RATING PLATE.

•This chart is for information only. For satisfactory operation, external static pressure should not exceed value shown on the rating plate.

•The above chart is for U.S. furnaces installed at 0-2000 feet. At higher altitudes, a properly derated unit will have approximately the same temperature rise at a particular CFM, while ESP at the CFM will be lower.

•Factory Motor Speed Setting: T1 = 1st Stage Ht, T2 = 2nd Stage Ht, T5 = Cooling

•Tempertaure rise data is based on 2nd-stage heat. First-stage heat is 75% of rise indicated above.

SS-GME8 www.goodmanmfg.com 5