Graco 312359J Configure to Supply Power

Setup

20 312359J

Configure to Supply Power

(Non-hazardous location sprayers only.)

NOTE:

Disregard terminal numbers on disconnect switch

blocks. Wire to positions shown.

1. Locate power jumpers.

2. Use a flat-blade screwdriver to move red jumpers

from storage positions to positions for your power as

shown below. Push jumpers firmly into new position.

NOTE:

For 230V, 1 Phase and 230V, 3 Phase Installations,

change jumper positions as shown below. Machine is

shipped with jumpers in the fail-safe 380 3Ø position.

3. Close junction box cover.

ti18664a

Power

Jumpers

L3 L2 L1 N

230V 1ø

L3 L2 L1 N

230V 3ø Delta

L3 L2 L1 N

380V 3ø WYE

TB2

Termin al Blo cks

Position red jumpers

as shown

(as shipped)

Contents

Main Operation XM Plural-Component Sprayers Contents Related Manuals Warn ings WARNINGWARNINGWARNING Page Page Models Intrinsically safe for Class I, Div 1, Group D, T2 Class I, Division 1, Group D, T2 Ta = 0C to 54C FM09ATEX0015X II 2 G Ex d ia px IIA T2 Tamb = 0C to 54C Overview Usage Isocyanate Hazard Material Self-Ignition Moisture Sensitivity of Isocyanates Components A and B Keep Components A and B Separate Changing Materials Location Grounding Proper Lifting of Sprayer Lift Using a Forklift Lift Using a Hoist Initial System Setup Component Identification Typical Setup: 20 Gallon Hoppers with Recirculation (Front View) M FIG. 1: Typical Setup: 20 Gallon Hoppers with Recirculation (Front View) Typical Setup: 20 Gallon Hoppers with Recirculation (Back View) FIG. 2: Typical Setup: 20 Gallon Hoppers with Recirculation (Back View) Fluid Control Assembly FIG. 3: Fluid Control Assembly Junction Box/Heater Controls FIG. 4: Junction Box/Heater Controls Air Controls FIG. 5: Air Controls User Interface FIG. 6: User Interface Buttons LEDs There are four types of LEDs on the display. DA DB User Interface Display Setup Connect Power Cord (For sprayers with heater junction boxes. Non-hazardous location sprayers only.) Configure to Supply Power (Non-hazardous location sprayers only.) 230V 3 Delta 230V 1 380V 3 WYE Wire Sprayers with Explosion-Proof Heaters (Hazardous location sprayers only) Connect Air Supply Connect Fluid Hose Assembly Adjust Packing Nuts Basic Operation Power On (Alternator Power Supplied Systems) Power On (Wall Power Supplied Systems) Adjust Ratio and Setup Final Setup Set System Settings (Optional) Set User Interface Parameters Set USB Parameters Set Maintenance Parameters (Optional) Set Sprayer Limits (Optional) Prime Prime A and B Fluids Page Prime Solvent Flush Pump Recirculate Without Heat With Heat Heat Fluid Spray Adjust B Machine Outlet Restriction Pressure Relief Procedure Relieve A and B Fluid Pressure Relieve Pump Fluid Pressure and Flush Mix Hose Page Flush Mixed Material Flush Mix Manifold Page Park Fluid Pump Rods Shutdown Entire System System Verification Mix and Integration Tests Butterfly Test Curing Test Appearance Test Page Confirm Pump Test Batch Ratio Dispense Test Confirm Batch Dispense Test Down Stream Valve Leak Test XM Setup and Troubleshooting Guide Grounding Air Supply Calibration Motor Icing Empty and Flush Entire System (new sprayer or end of j ob) Guidelines Procedure Page Download Data from USB USB Logs Download Setup Download Procedure Page Maintenance Filters Seals Cleaning Procedure Alarms View Alarms Diagnose Alarms Clear Alarms Alarm Codes and Troubleshooting General Performance Alarms Page Pump Test (Daily Check Recommended) General System Component Alarms Alarm Optional User-Settable Maintenance Warnings Alarm Optional User-Settable Spray Limits Alarm Possible Alarms by Mode Alarm Code Key LED Diagnostic Information Accessories and Kits Page Appendix A User Interface Display Setup Mode Screens Home Setup Screens Icon Function A B A+B System Setup Screens Icon Function Page Enable Setup Screens Icon Function Maintenance Setup Screens Icon Function User Limits Setup Screens Icon Function Operator Command Functions Screens Run (Fluid Control) Screens Test Screens Alarm Control Screens Run (Fluid Control) Screens Icon Function Test Screens Icon Function Page Alarm Control Screens Icon Function Page Auto Display Screens Potlife Screen USB Screen Icon Function Page Appendix B Metering Diagrams Metering Diagram without Remote Mix Manifold A B A B XM Metering Diagram with Remote Mix Manifold Appendix C 312359J 79 Appendix C Power Cord Guidelines Table 3: Power Cord Guidelines Dimensions System Dimensions without Hoppers Page System Dimensions with Hoppers One 20-Gallon Hopper and One 7-Gallon Hopper Two 7-Gallon Hoppers Pump Performance Charts Calculate Fluid Outlet Pressure Calculate Pump Air Consumption XM50 Fluid Performance and Air Consumption XM70 Fluid Performance and Air Consumption Technical Data Page Graco Standard Warranty Graco Information