Troubleshooting
|
| WHAT TO CHECK |
| WHAT TO DO |
TYPE OF PROBLEM | If check is OK, go to next check | When check is not OK, refer to this column | ||
|
|
|
|
|
Pump output is low | 1. | Spray tip worn | 1. | Follow Pressure Relief Procedure on |
|
|
|
| page 8, then replace tip. See your sepa- |
|
|
|
| rate gun or tip manual. |
|
|
|
|
|
| 2. | Spray tip clogged | 2. | Relieve pressure. Check and clean spray |
|
|
|
| tip. |
|
|
|
|
|
| 3. | Paint supply | 3. | Refill and reprime pump. |
|
|
|
|
|
| 4. | Intake strainer clogged | 4. | Remove and clean, then reinstall |
|
|
|
|
|
| 5. | Intake valve ball and piston ball | 5. | Remove intake valve and clean. Check |
|
| are not seating properly |
| balls and seats for nicks; replace if neces- |
|
|
|
| sary; see pump manual 310643 or |
|
|
|
| 310894. Strain paint before using to |
|
|
|
| remove particles that could clog pump. |
|
|
|
|
|
| 6. | Suction hose connections | 6. | Tighten any loose connections. Check for |
|
|
|
| missing or damaged seals. |
|
|
|
|
|
| 7. | Fluid filter, tip filter, or tip is | 7. | Clean filter; see operation manual. |
|
| clogged or dirty. |
|
|
|
|
|
| |
| 8. | Prime valve leaking | 8. Relieve pressure. Repair prime valve. | |
|
|
|
|
|
| 9. | Verify pump does not continue to | 9. | Service pump; see pump manual 310643 |
|
| stroke when gun trigger is |
| or 310894. |
|
| released. (Prime valve not leak- |
|
|
|
| ing.) |
|
|
|
|
|
|
|
| 10. | Leaking around throat packing | 10. | Replace packings; see pump manual. Also |
|
| nut which may indicate worn or |
| check piston valve seat for hardened paint |
|
| damaged packings. |
| or nicks and replace if necessary. Tighten |
|
|
|
| packing |
|
|
|
|
|
| 11. | Pump rod damage | 11. | Repair pump. See pump manual 310643 |
|
|
|
| or 310894. |
|
|
|
|
|
| 12. | Low stall pressure | 12. | Turn pressure knob fully clockwise. Make |
|
|
|
| sure pressure control knob is properly |
|
|
|
| installed to allow full clockwise position. If |
|
|
|
| problem persists, replace pressure trans- |
|
|
|
| ducer. |
|
|
|
|
|
| 13. | Piston packings are worn or | 13. | Replace packings; see pump manual |
|
| damaged |
| 310643 or 310894. |
|
|
|
|
|
| 14. | 14. | Replace | |
|
| aged |
| or 310894. |
|
|
|
|
|
| 15. | Intake valve ball is packed with | 15. | Clean intake valve; see pump manual |
|
| material |
| 310643 or 310894. |
|
|
|
|
|
| 16. | Pressure setting is too low | 16. | Increase pressure; see pump manual |
|
|
|
| 310643 or 310894. |
|
|
|
|
|
| 17. | Large pressure drop in hose with | 17. | Use larger diameter hose and/or reduce |
|
| heavy materials |
| overall length of hose. Use of more than |
|
|
|
| 100 ft of 1/4 in. hose significantly reduces |
|
|
|
| performance of sprayer. Use 3/8 in. hose |
|
|
|
| for optimum performance (50 ft minimum). |
|
|
|
|
|
3A0157B | 11 |
