CeramTip Kits, Round CeramTip Part Numbering Code | Graco TI3840a

Parts

CeramTip Kits

Round CeramTip Part Numbering Code

Example	First Three Digits			Last Three Digits
Part No.


RTM055	RTM=Round CeramTip mechanical purge			Equivalent orifice diameter size (.055 in.)

Round CeramTips (include drill bit)

CeramTip Part No.		Drill Bit Size, nominal**


RTM024		#73

RTM030		#67

RTM040		#60

RTM055		#54

RTM070		#50

RTM080		2.0 mm

RTM090		#43

RTM100		#39

RTM110		7/64

**For further information, see identification chart under Drill Bit Kits, page 51.

Flat CeramTip Part Numbering Code

Example	First Three Digits		Fourth Digit		Last Two Digits
Part No.


FTM848	FTM=Flat CeramTip mechanical purge		8x2=pattern length		Equivalent orifice diameter size
			(8x2=16 in.)		(.048 in.)

Flat CeramTips

CeramTip Part No.		Pattern Size, in. (mm)


FTM317		very low flow, 6-8 (152-203)

FTM424		low flow, 8-10 (203-254)

FTM438		medium flow, 8-10 (203-254)

FTM624		low flow, 12-14 (305-356)

FTM638		medium flow, 12-14 (305-356)

FTM838		medium flow, 16-18 (406-457)

FTM848		high flow, 16-18 (406-457)

50

309856U

Image 50

Graco TI3840a CeramTip Kits, Round CeramTip Part Numbering Code, Flat CeramTip Part Numbering Code, Flat CeramTips

Contents

Important Safety Instructions Plural Component, Impingement Mix Mechanical Purge Spray Gun Contents Manual Conventions Pressure in psi MPa, bar List of Models/Selection GuideStandard Round Pattern Guns Standard Flat Pattern Guns 247291, a Direct Impingement Round Pattern Guns Flow Rate in gpm lpm Direct Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Overall View Key Keep a and B Components Separate Piston Safety LockIsocyanate Hazard Grounding Setup ISO Disengage piston safety lock, Adjust Purge Rod 1/4 Turn Adjust Flat CeramTip Daily Shutdown Follow Pressure Relief Procedure,Shutdown Shutdown for More than a Day Pressure Relief Procedure Optional Configurations Optional Fluid Manifold Position Fluid Hoses Follow Pressure Relief Procedure, page 18. AlsoOptional Hose Position Air Hose Maintenance Clean Muffler Clean Outside of GunClean Air Cap Clean Fluid Manifold Clean Slip-Fit Polycarballoy Mix Module Cleaning Component a ISO Ports Impingement Port Cleanout Drill Sizes XF1313 #81 Cleanout Drill Sizes for Round CeramTips Clean CeramTipExternal Quick Cleaning Method Round CeramTip Stuck Purge Rod Clean Purge RodAdjust Purge Rod, Disassemble Front End, Adjust Front Rod SealReassemble Front End, Adjust Purge Rod, Adjust Rear Rod Seal Troubleshooting See Clean Purge Rod, Adjust Rear Rod Seal, Gun Detriggered Mechanical Purging Theory of OperationGun Triggered Fluid Spraying Cutaway View Lubrication RepairTools Required Replace CeramTip Disassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Piston Safety Lock Air Valve 309856U Parts Flush Manifold Detail Part No. Description Qty Handle Standard Round Pattern Guns Slip-Fit Polycarballoy Mix Module KitsSlip-Fit Polycarballoy Mix Module Part Numbering Code Standard Flat Pattern Guns Direct Impingement Round Pattern Guns Direct Impingement Flat Pattern Guns Flat CeramTip Part Numbering Code CeramTip KitsRound CeramTip Part Numbering Code Flat CeramTips Drill Bit Kits Kit Part No Qty in Kit Drill Bit Size Illustration Nominal Gun Repair Kits Check Valve Filter Screen Kits 10 per kit Accessories Pour Nozzle Kit Solvent Flush Pail KitHose Adapter Kits Technical Data Category Data Toll Free Graco Standard WarrantyGraco Information