Pressure Relief Procedure | Graco TI3840a specs

Pressure Relief Procedure

Pressure Relief Procedure

WARNING

Read warnings, page 9. Relieve pressure before cleaning or repairing gun.

1. Engage piston safety lock, page 12.

TI3850a

Air supply is required for gun actuation. Do not disconnect gun air supply until fluid pressure is relieved.

2. Close fluid valves A and B. Leave air valve (U)

open.

BU

TI3837a

A

3. Disengage piston safety lock, page 12.

4. Trigger gun onto cardboard or into waste container

to relieve pressure.

TI4243a

5. Engage piston safety lock, page 12.

TI3850a

WARNING

If fluid in the hose and proportioner is still under pres- sure, follow the Pressure Relief Procedure in the pro- portioner manual.

To relieve pressure in the hose after the gun is removed, place the fluid manifold over containers, fac- ing away from you. Very carefully open the fluid valves. Under high pressure, fluid will spray sideways from the fluid ports.

TI3849a

TI2484A

18

309856U

Image 18

Graco TI3840a important safety instructions Pressure Relief Procedure

Contents

Important Safety Instructions Plural Component, Impingement Mix Mechanical Purge Spray Gun Contents Manual Conventions List of Models/Selection Guide Standard Round Pattern GunsPressure in psi MPa, bar Standard Flat Pattern Guns 247291, a Direct Impingement Round Pattern Guns Flow Rate in gpm lpm Direct Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Overall View Key Keep a and B Components Separate Piston Safety LockIsocyanate Hazard Grounding Setup ISO Disengage piston safety lock, Adjust Purge Rod 1/4 Turn Adjust Flat CeramTip Daily Shutdown Follow Pressure Relief Procedure,Shutdown Shutdown for More than a Day Pressure Relief Procedure Optional Configurations Optional Fluid Manifold Position Fluid Hoses Follow Pressure Relief Procedure, page 18. AlsoOptional Hose Position Air Hose Maintenance Clean Muffler Clean Outside of GunClean Air Cap Clean Fluid Manifold Clean Slip-Fit Polycarballoy Mix Module Cleaning Component a ISO Ports Impingement Port Cleanout Drill Sizes XF1313 #81 Cleanout Drill Sizes for Round CeramTips Clean CeramTipExternal Quick Cleaning Method Round CeramTip Clean Purge Rod Adjust Purge Rod,Stuck Purge Rod Adjust Front Rod Seal Reassemble Front End, Adjust Purge Rod,Disassemble Front End, Adjust Rear Rod Seal Troubleshooting See Clean Purge Rod, Adjust Rear Rod Seal, Theory of Operation Gun Triggered Fluid SprayingGun Detriggered Mechanical Purging Cutaway View Lubrication RepairTools Required Replace CeramTip Disassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Piston Safety Lock Air Valve 309856U Parts Flush Manifold Detail Part No. Description Qty Handle Standard Round Pattern Guns Slip-Fit Polycarballoy Mix Module KitsSlip-Fit Polycarballoy Mix Module Part Numbering Code Standard Flat Pattern Guns Direct Impingement Round Pattern Guns Direct Impingement Flat Pattern Guns Flat CeramTip Part Numbering Code CeramTip KitsRound CeramTip Part Numbering Code Flat CeramTips Drill Bit Kits Kit Part No Qty in Kit Drill Bit Size Illustration Nominal Gun Repair Kits Check Valve Filter Screen Kits 10 per kit Accessories Solvent Flush Pail Kit Hose Adapter KitsPour Nozzle Kit Technical Data Category Data Graco Standard Warranty Graco InformationToll Free