Maintenance | Graco TI3840a instruction

Maintenance

Maintenance

Supplied Tool Kit

•Hex Nut Driver; 5/16

•Screwdriver; 1/8 blade

•CeramTip Drill Bit; various sizes depending on CeramTip size. See TABLE 2, page 26.

•Mix Module Drill Bit; various sizes depending on port size. See TABLE 1, page 24.

•117661 Pin Vise; dual reversible chucks Reversible

Reversible

TI3864a

•15B817 Flush Manifold

Keep Gun Clean

Keep gun clean with accessory gun cover, page 53.

Applying a light coat of lubricant will make cleaning eas- ier. Lubricate threads and outside of lock ring (11) to ease disassembly. Use Fusion Gun Lubricant, page 53.

As Needed

1. Clean Outside of Gun, page 22.

2. Clean CeramTip, page 26, a minimum of once a

day.

3. Clean Air Cap, page 22.

4. Clean Muffler, page 22.

5. Clean Fluid Manifold, page 22.

6. Clean Slip-Fit Polycarballoy Mix Module, page

23.

Daily

Follow Shutdown, page 17.

Weekly to Monthly

1. Clean Purge Rod, page 27.

2. Clean Check Valves, page 41. Check o-rings and screens.

3. Check that piston safety lock threaded connection is tight, page 44.

309856U

21

Image 21

Graco TI3840a important safety instructions Maintenance

Contents

Plural Component, Impingement Mix Mechanical Purge Spray Gun Important Safety Instructions Contents Manual Conventions List of Models/Selection Guide Standard Round Pattern GunsPressure in psi MPa, bar 247291, a Standard Flat Pattern Guns Flow Rate in gpm lpm Direct Impingement Round Pattern Guns Direct Impingement Flat Pattern Guns Four-Hose Gun Personal Protective Equipment Fire and Explosion Hazard Key Overall View Isocyanate Hazard Piston Safety LockKeep a and B Components Separate Grounding ISO Setup Disengage piston safety lock, 1/4 Turn Adjust Purge Rod Adjust Flat CeramTip Shutdown Follow Pressure Relief Procedure,Daily Shutdown Shutdown for More than a Day Pressure Relief Procedure Optional Fluid Manifold Position Optional Configurations Optional Hose Position Follow Pressure Relief Procedure, page 18. AlsoFluid Hoses Air Hose Maintenance Clean Air Cap Clean Outside of GunClean Muffler Clean Fluid Manifold Cleaning Component a ISO Ports Clean Slip-Fit Polycarballoy Mix Module Impingement Port Cleanout Drill Sizes XF1313 #81 External Quick Cleaning Method Clean CeramTipCleanout Drill Sizes for Round CeramTips Round CeramTip Clean Purge Rod Adjust Purge Rod,Stuck Purge Rod Adjust Front Rod Seal Reassemble Front End, Adjust Purge Rod,Disassemble Front End, Adjust Rear Rod Seal See Clean Purge Rod, Troubleshooting Adjust Rear Rod Seal, Theory of Operation Gun Triggered Fluid SprayingGun Detriggered Mechanical Purging Cutaway View Tools Required RepairLubrication Replace CeramTip Disassemble Front End Reassemble Front End Adjust Purge Rod, Slip-Fit Polycarballoy Mix Module Attach fluid manifold. Return gun to service Rear Rod Seal Check Valves Piston and Purge Rod Install piston safety lock assembly until bottomed out Air Valve Piston Safety Lock 309856U Flush Manifold Detail Parts Handle Part No. Description Qty Slip-Fit Polycarballoy Mix Module Part Numbering Code Slip-Fit Polycarballoy Mix Module KitsStandard Round Pattern Guns Standard Flat Pattern Guns Direct Impingement Flat Pattern Guns Direct Impingement Round Pattern Guns Round CeramTip Part Numbering Code CeramTip KitsFlat CeramTip Part Numbering Code Flat CeramTips Kit Part No Qty in Kit Drill Bit Size Illustration Nominal Drill Bit Kits Check Valve Filter Screen Kits 10 per kit Gun Repair Kits Accessories Solvent Flush Pail Kit Hose Adapter KitsPour Nozzle Kit Category Data Technical Data Graco Standard Warranty Graco InformationToll Free