| TABLE 10: |
|
| |||
|
|
|
|
|
| |
| SIP Server |
| This field contains the URI string or the IP address (and port, if different from |
| ||
|
|
|
| 5060) of the SIP proxy server. e.g., the following are some valid examples: |
| |
|
|
|
|
| ||
|
|
|
| 192.168.1.200:5066 |
|
|
|
|
|
|
|
| |
| Outbound Proxy |
|
| IP address or Domain name of Outbound Proxy, or Media Gateway, or |
| |
|
|
| Session Border Controller. Used by ATA for firewall or NAT penetration in |
| ||
|
|
|
| different network environment. If symmetric NAT is detected, STUN will not |
| |
|
|
|
| work and ONLY Outbound Proxy will work. |
|
|
|
|
|
|
| ||
| SIP User ID |
|
| User account information, provided by VoIP service provider (ITSP), usually |
| |
|
|
|
| has the form of digit similar to phone number or actually a phone number. This |
| |
|
|
|
| field contains the user part of the SIP address for this phone. e.g., if the SIP |
| |
|
|
|
| address is sip:my_user_id@my_provider.com, then the SIP User ID is: |
| |
|
|
|
| my_user_id. |
|
|
|
|
|
| Do NOT include the preceding “sip:” scheme or the host portion of the SIP |
| |
|
|
|
| address in this field. |
|
|
|
|
|
|
| ||
| Authenticate ID |
|
| ID used for authentication, usually same as SIP user ID, but could be different |
| |
|
|
|
| and decided by ITSP. |
|
|
|
|
|
|
| ||
| Authentication |
|
| Password for ATA to register to (SIP) servers of ITSP. Purposely blank out |
| |
| Password |
|
| once saved for security. Maximum length is 25. |
|
|
|
|
|
|
|
| |
| Name |
|
| User name, not user ID, for information only. |
|
|
|
|
|
|
| ||
| Use DNS SRV: |
|
| Default is No. If set to Yes the client will use DNS SRV to lookup for the server |
| |
|
|
|
|
| ||
| User ID is Phone |
|
| If the |
| |
| Number |
|
| set to “Yes”. Otherwise, set it to “No”. |
|
|
|
|
|
| . If set to yes, a “user=phone” parameter will be attached to the “From” header |
| |
|
|
|
| in SIP request |
|
|
|
|
|
|
| ||
| SIP Registration |
|
| This parameter controls whether the |
| |
|
|
|
| messages to the proxy server. The default setting is “Yes”. |
|
|
|
|
|
|
| ||
| Unregister On Reboot |
|
| Default is No. If set to Yes, the device will first send registration request to |
| |
|
|
|
| indicate SIP registra to remove previous bindings. |
|
|
|
|
|
|
| ||
| Register Expiration |
|
| This parameter allows the user to specify the time frequency (in minutes) the |
| |
|
|
|
|
| ||
|
|
|
| interval is 60 minutes (or 1 hour). The maximum interval is 65535 minutes |
| |
|
|
|
| (about 45 days). |
|
|
|
|
|
|
| ||
| Local SIP port |
|
| This parameter defines the local SIP port the |
| |
|
|
|
| The default value is for FXS1 is 5060, FXS2 is 5062 |
|
|
|
|
|
|
| ||
| Local RTP port |
|
| This parameter defines the local |
| |
|
|
|
| and transmit. It is the base RTP port for channel 0. When configured, channel |
| |
|
|
|
| 0 will use this port_value for RTP and the port_value+1 for its RTCP; channel |
| |
|
|
|
| 1 will use port_value+2 for RTP and port_value+3 for its RTCP. The default |
| |
|
|
|
| value for FXS1 is 5004, FXS2 is 5008. |
|
|
|
|
|
|
| ||
| Use Random Port |
|
| Default No. If set to Yes, the device will pick |
| |
|
|
|
| ports. This is usually necessary when multiple SIP devices are behind the |
| |
|
|
|
| same NAT. For Direct IP to IP call, this should be set to No. |
| |
|
|
|
|
| ||
| DTMF Payload Type |
|
| This parameter sets the payload type for DTMF using RFC2833 |
| |
|
|
|
|
| ||
| Send DTMF |
|
| This parameter specifies the mechanism to transmit DTMF digit. There are 3 |
| |
|
|
|
| modes supported: in audio which means DTMF is combined in audio signal |
| |
|
|
|
| (not very reliable with |
| |
|
|
|
|
|
|
|
| Grandstream Networks, Inc. |
| Page 23 of 34 |
| ||
|
|
|
| Firmware 1.0.3.64 | Last Updated: 2/2007 |
|
