Manuals / Grizzly / Kitchen Appliance / Mixer

Grizzly G0484 Table of Contents, Setup, Operations, Maintenance, Service, Warranty And Returns

Models: G0484

1 48

Download 48 pages 39.33 Kb

Page 3

Table of Contents

INTRODUCTION	2
Foreword	2
Contact Info	2
Machine Data Sheet	3
Identification	5
SECTION 1: SAFETY	6
Additional Safety Instructions for Mill/Drills....	8
SECTION 2: CIRCUIT REQUIREMENTS	9
220V Single-Phase	9
SECTION 3: SETUP	10
Setup Safety	10
Items Needed for Setup	10
Unpacking	10
Inventory	11
Clean Up	11
Site Considerations	12
Moving & Placing Base Unit	12
Mounting to Shop Floor	13
Assembly	13
Test Run	14
Break-In	15
SECTION 4: OPERATIONS	16
Operation Safety	16
Control Panel	16
Spindle Height Control	17
Table Travel	17
(X-Axis and Y-Axis)	17
Headstock Travel	17
(Z-Axis)	17
Tooling Changes	18
Choosing Spindle RPM	19
Milling/Drilling	20

SECTION 5: ACCESSORIES	21
SECTION 6: MAINTENANCE	23
Schedule	23
Cleaning and Protecting	23
Lubrication	24
SECTION 7: SERVICE	26
Troubleshooting	26
Adjusting Gibs	27
G0484 Wiring Diagram	28
220V Single Phase	28
Electrical Component Index	29
Table Parts Breakdown	32
Column Parts Breakdown	34
Head Parts Breakdown, Part A	36
Head Parts Breakdown, Part B	37
Label Placement	40
WARRANTY AND RETURNS	41

Image 3

Grizzly G0484 owner manual Table of Contents, Setup, Operations, Maintenance, Service, Warranty And Returns

Contents

MODEL G0484 GEARHEAD MILL/DRILL WITH STAND Page SECTION 7 SERVICE Table of ContentsSECTION 3 SETUP SECTION 6 MAINTENANCEINTRODUCTION ForewordContact Info G0484 Gear Head Mill/Drill Machine Data SheetG0484 Gear Head Mill/Drill Identification G0484 Gear Head Mill/Drill G0484 Gear Head Mill/Drill Additional Safety Instructions for Mill/Drills Circuit Requirements 220V Single-PhaseSECTION 2 CIRCUIT REQUIREMENTS Amperage DrawUnpacking SECTION 3 SETUPSetup Safety Items Needed for SetupClean Up Clean Up InventoryInventory Floor Load Placement LocationSite Considerations Moving & Placing Base UnitTo assemble your mill/drill AssemblyMounting to Shop Floor Mounting to Shop FloorTo test run the machine Test RunTo perform the break-in procedure Break-InOperation Safety SECTION 4 OPERATIONSControl Panel To change the spindle position Spindle Height ControlTable Travel X-Axis and Y-Axis Headstock Travel Z-AxisTooling Changes To install tooling in the spindleTo remove tooling from the spindle Choosing Spindle RPM 3. Refer to Choosing Spindle RPM on Page Milling/Drillingmay threaten operator safety To mill a workpieceG9324-Boring Head Combo Set SECTION 5 ACCESSORIESACCESSORIES H2689-R-8 Quick Change Collet SetG9765-9-PC. Ball End Mill Set SECTION 6 MAINTENANCE Cleaning and ProtectingSchedule Longitudinal and Cross Lead Screws LubricationBall Oilers WaysTo change the headstock oil Headstock Lead ScrewHeadstock Gearbox Oil To clean and lubricate the lead screwMotor & Electrical SECTION 7 SERVICETroubleshooting TroubleshootingAdjusting Gibs G0484 Gear Head Mill/Drill G0484 Wiring Diagram 220V Single PhasePage Electrical Component IndexELECTROCUTION HAZARD PageFigure 37. Spindle motor capacitors and wiring connections Figure 34. Spindle motor rotary switch left and right viewFigure 35. Lift motor capacitor and wiring box Figure 36. Master power switchG0484 Gear Head Mill/Drill Figure 39. Main wiring boxG0484 Gear Head Mill/Drill Table Parts BreakdownPART # Table Parts ListPART # DESCRIPTIONG0484 Gear Head Mill/Drill Column Parts BreakdownPART # Column Parts ListPART # DESCRIPTIONHEAD A Head Parts Breakdown, Part AHEAD B Head Parts Breakdown, Part BPART # Head Parts ListPART # DESCRIPTIONPART # Head Parts ListPART # DESCRIPTIONDESCRIPTION Label Placement402 404 REF PART #WARRANTY AND RETURNS Page Page Page