Manuals / Grizzly / Power Tools / Saw

Grizzly G0514 Test Run Tensioning Blade, To test run the machine, To tension the bandsaw blade

Models: G0514

1 68
Download 68 pages 42.15 Kb
Page 25
Image 25

Test Run

 

Tensioning Blade

 

 

 

 

 

 

Once the assembly is complete, test run your machine to make sure it runs properly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on Page 40.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1.Make sure you have read the safety instruc- tions at the beginning of the manual and that the machine is set up properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Make sure the blade has been tracked and tensioned according to the "Blade Tracking" instructions on Page 19.

4.Connect the machine to the power source.

5.Turn the machine ON.

6.Listen to and watch for abnormal noises or actions. The machine should run smoothly with little or no vibration or rubbing noises.

—Strange or unusual noises should be inves- tigated and corrected before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

7.Turn the machine OFF.

Model G0513/G0514 (Mfg. since 8/02+)

A properly tensioned blade is essential for making accurate cuts and is required before making many bandsaw adjustments. (Everytime you replace the blade, you should perform this procedure because all blades tension differently.)

To tension the bandsaw blade:

1.Complete the Test Run procedure and make sure the blade is tracking properly.

2.Raise the upper blade guide assembly as high as it will go, and adjust the upper and lower guide blocks as far away from the blade as possible. Note: This procedure will NOT work if the guide blocks have any contact with the blade.

3.Engage the quick tension lever to the tight- ened position and turn the blade tension handwheel until the tension scale reads between 4 and 6.

4.Turn the bandsaw ON.

5.Slowly release the tension one quarter of a turn at a time. When you see the bandsaw blade start to flutter, stop decreasing the ten- sion.

6.Now, slowly increase the tension until the blade stops fluttering, then tighten the tension another quarter turn.

7.Look at what the tension gauge reads and use that as a guide for tensioning that blade in the future. Note: Always detension the blade after use to increase blade life and reduce strain on the bandsaw components.

8.Re-adjust the blade tracking as instructed on

Page 19.

-23-

Page 24 Page 26
Page 25
Image 25
Grizzly G0514 owner manual Test Run Tensioning Blade, To test run the machine, To tension the bandsaw blade
Page 24 Page 26

G0514 specifications

The Grizzly G0514 is a top-tier bandsaw designed specifically for serious woodworkers and industrial applications. This machine is celebrated for its powerful cutting capabilities and precision, making it a vital tool for anyone looking to handle large projects with ease.

One of the standout features of the Grizzly G0514 is its robust 2 HP, 220V motor that provides ample power for cutting through thick hardwoods, softwoods, and even non-ferrous metals. This strong motor ensures a stable performance, enabling users to tackle various cutting tasks without worrying about overheating or stalling. Complementing this motor is a dual voltage capability, allowing users to switch between 120V and 220V power sources, making it incredibly versatile for different workshops.

The Grizzly G0514 also boasts a large 17-inch throat capacity, which translates to an impressive resaw height of 12 inches. This means that woodworkers can rip large pieces of timber or veneer with remarkable ease. The 14-inch blade length further enhances its cutting capabilities, providing smooth and clean cuts every time.

Another significant characteristic of this bandsaw is the precision-bearing blade guides. These guides ensure that the blade remains stable during operation, reducing blade deflection and enhancing the quality of cuts. The G0514 is equipped with a heavy-duty cast iron frame and base, which not only ensures stability and durability but also helps minimize vibrations—giving users a smoother cutting experience.

Featuring a rich array of technologies, the Grizzly G0514 is built with user-friendliness in mind. The quick-release blade tension lever allows for speedy adjustments when switching blades, maximizing efficiency. Additionally, it comes with a full-size table measuring 22 inches by 27 inches, providing ample workspace for larger projects.

Safety is paramount in woodworking, and this bandsaw is no exception, featuring a blade brake and an integrated dust port that helps maintain a clean work environment. The G0514 also comes equipped with a fence and miter gauge, enabling accurate cuts and angled woodworking tasks.

In summary, the Grizzly G0514 is an excellent choice for both professional woodworkers and hobbyists alike. With its powerful motor, vast cutting capacity, and user-friendly features, it stands out as a reliable and high-performance bandsaw in the market. Whether you’re crafting intricate furniture or simply doing home projects, the G0514 is designed to meet all your woodworking needs efficiently and safely.