Manuals / Grizzly / Power Tools / Saw

Grizzly G0555X owner manual Labels Parts Breakdown

Models: G0555X

1 60

Download 60 pages 45.77 Kb

Page 54

Labels Parts Breakdown

��

��

��

��

��

REF	PART #	DESCRIPTION

401	P0555X401	MACHINE ID LABEL
402	PLABEL-20	DON'T OPEN LABEL
403	PLABEL-19	HAND/BS BLADE LABEL
404	PLABEL-18	UNPLUG BANDSAW LABEL
405	P0555X405	G0555X MODEL NUMBER LABEL

��

��

��

��

��

��

REF	PART #	DESCRIPTION

406	PLABEL-11	WEAR SAFETY GLASSES LABEL
407	P0555X407	LAMP WARNING LABEL
408	P0555X408	"GRIZZLY GREEN" COLOR PAINT
409	P0555X409	"PUTTY" COLOR PAINT
410	P0555X410	BULB DESTRUCTION LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-52-	G0555X 14" Extreme Series Bandsaw

Image 54

Grizzly G0555X owner manual Labels Parts Breakdown

Contents

Model G0555X Extreme Series Bandsaw Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery G0555X 14 Extreme Series Bandsaw Additional Safety Instructions for Bandsaws Amperage Draw Circuit Requirements110V/220V Operation Circuit RequirementsGrounding Extension Cords Items Needed for Setup SET UPSet Up Safety UnpackingInventory Main Components Figure QtyFasteners and Tools not shown Qty Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the bandsawExtension table installed G0555X 14 Extreme Series Bandsaw G0555X 14 Extreme Series Bandsaw Dust Collection Blade Tracking To connect a dust collection hoseTo center track the blade Test Run Changes in the blade tension may change the blade trackingTensioning Blade Adjusting Support BearingsTo adjust the support bearings To tension the bandsaw bladeG0555X 14 Extreme Series Bandsaw Adjusting Blade Guides To adjust the upper and lower blade guidesTo set the positive stop 90˚ to the blade Adjusting Positive StopSetting Table Tilt Scale to 0˚ To calibrate the pointer on the table tilt scaleLeveling Extension To level the extension tableRepeat Steps To align the miter slot parallel to the bandsaw blade Aligning TableAligning Fence To align the fence parallel with the miter slotOperation Safety OperationsOverview Guide Post Table TiltTo tilt the table RippingCrosscutting To make a rip cutTo make a 90˚ crosscut Resawing Typical resawing operationCutting Curves Stacked Cuts To complete a stacked cutBlade Width Blade InformationBlade Length Tooth StyleBlade Breakage Tooth PitchBlade Care Grizzly Bandsaw BladesBlade Changes To remove the bladeTo replace the blade Scale Calibration To calibrate the scaleAccessories Extension Block Kit H3051G1928-Bandsaw Handbook Schedule MaintenanceCleaning LubricatingService TroubleshootingMotor & Electrical Cutting Operations MiscellaneousTo check the belt Checking BeltTensioning Belt To tension the beltReplacing Belt To replace the beltShimming Table Blade Lead To shim the tableTo skew your fence Wheel Alignment To verify if the upper and lower wheels are coplanarCoplanar diagram G0555X 14 Extreme Series Bandsaw Shimming a wheelTo reset the blade tensioner Blade Tensioner110V Wiring Diagram Prewired 220V Wiring Diagram Main Main Parts List DescriptionPSB31M Secondary Parts Breakdown Lamp Stand Parts Breakdown Labels Parts Breakdown Warranty and Returns G0555X 14 Extreme Series Bandsaw Page Page