Accessories, H8179, H8177-Worktable with Angle | Grizzly G0704

ACCESSORIES

SECTION 5: ACCESSORIES

Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly.

NOTICE

Refer to www.grizzly.com or the newest copy of the Grizzly Catalog for other acces- sories available for this machine.

H8179—Horizontal Milling Table

Take advantage of the G0704 mill/drill 90° tilting headstock feature. Install this lifted cast-iron hori- zontal milling table for the correct clearance when making those side-milling operations.

H8179

Figure 33. Horizontal milling worktable.

H8177—Worktable with Angle

Enjoy having an economical way to support your workpiece at an array of angles. This high-quality tilting worktable is quick and easy to setup and use.

Figure 34. Worktable with angle.

T10063—Milling Vise 125⁄16" x 69⁄16" T10064—Milling Vise 171⁄8" x 83⁄4"

•Ultra precise in flatness, parallelism and ver- ticality.

•Anti-lift mechanism ensures the workpiece does not lift when jaws are tightened.

•Ductile iron body.

•Flame hardened vise bed and jaws.

•Sealed bearing system.

•8200 lbs. of clamping pressure.

Figure ??. T10064 Milling vise (handle included,

but not shown.

Model G0704 (Mfg. since 09/09)

-33-

Image 35

Grizzly G0704 owner manual Accessories, H8179, H8177-Worktable with Angle

Contents

Model G0704 MILL/DRILL with Stand Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification G0704 electronic controls identification Electronic Controls Identification Machine Data Sheet Other Features Safety Instructions for Machinery Safety Unattended OPERATION. Never leave Additional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWG Description Qty SetupNeeded for Setup Unpacking Not Shown Contents QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Weight Load Moving & Placing Machine Example of a direct mount setup Bolting to Concrete Floors Mounting to Shop Floor To assemble your machine AssemblyTo install the drill chuck onto the arbor Drill Chuck Arbor Connecting Power Power Connection To test run and break-in the spindle bearings Test Run & Spindle Break-in Speed Range Selector Knob Selects low range OperationsBasic Controls Digital readout unit controls Operation Overview To use the digital readout Digital Readout Unit To determine the needed spindle speed Calculating Spindle Speed To set the spindle speed Spindle Speed Direction Spindle Height Controls Changing Spindle Position Using Quill Feed Levers Drill Chuck To install the drill chuck and arbor To remove the collet To install the toolingLoading Tooling To tilt the headstock to the left or right Headstock Travel Axis and RotationTo raise or lower the headstock Cross Feed Table TravelLongitudinal Feed H8177-Worktable with Angle AccessoriesH8179 H5685-4Rotary Table G9322-Boring Head Combo SetG8683Z-Mini Shop Fox Mobile Base G5684-R-8 Vertical Collet Rack G5758-Tilt x Lubrication MaintenanceSchedule To lubricate the leadscrews Tools Needed Qty Handwheel gears Troubleshooting Service For proper use and safety Gibs To adjust the table gibsTo adjust the headstock gibs To replace the digital readout unit battery Battery ReplacementTo adjust the Y-axis leadscrew nut To adjust the X-axis leadscrew To inspect and replace the motor brushes Motor Service Wiring Safety Instructions Wiring 110 VAC Wiring Diagram Side panel Rear panel Column Breakdown Parts Description Column Parts List Electrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. since 09/09 Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Warranty and Returns Warranty and Returns Order Hours a DAY